EEWORLDEEWORLDEEWORLD

Part Number

Search

026Y224R102A1D

Description
Industrial 15/16 inch (24mm) Diameter, 5-Watt, Wirewound Variable Resistors
File Size766KB,4 Pages
ManufacturerCTS [CTS Corporation]
Download Datasheet View All

026Y224R102A1D Overview

Industrial 15/16 inch (24mm) Diameter, 5-Watt, Wirewound Variable Resistors

Series 026
®
Industrial 15/16"
(24mm) Diameter,
5-Watt, Wirewound
Variable Resistors
Features
Dust-proof construction
Water splash proof construction available
5-watt power rating
Superior resistance stability in temperature
and environment change
Tandem constructions available
Bushing or twist tab mounting
power switches
Excellent linearity performance
• RoHS compliant
Available with pull-push and rotary
Electrical and Mechanical Specifications
Resistance Range
Linear : 1 ohm through 25K ohms
Audio : 20 ohms through 10K ohms
Resistance Tolerance
Standard : ± 10%
Special : Tighter tolerance available in most
resistance values
Power Rating
5 watts @25°C, 4 watts @ 55°C, derated to
no load at 105°C, linear taper
(Derating required on two section countols.)
Voltage Rating
Bushing to Terminals:
High pot test, one minute -- 1,000 VAC
Operating maximum -- 500 VDC
Across End Terminals:
350 VDC maximum, load not to exceed
wattage rating.
Resistance Tapers
Standard: Linear or 20% audio
Special: Consult CTS
Linearity
Standard: 3% linearity
Special: Consult CTS
Power Switches
Rotary Pole-SPST, DPST & SPDT
Pull-Push Pole-SPST (Pull-ON, Push-OFF)
Rotational Angle
Mechanical Rotation:
Without switch: 300°±5°
With switch:
300°±5°
Effective Rotation:
Without switch: 280°±5°
With switch:
265°±5°
Rotational Torque:
Standard: 3/4 to 6 in. oz (54 - 432 gf-cm)
Special: higher torque models available, consult CTS
Operating Temperature
-30°C to +85°C
(continued on next page)
1-4
CTS Electronic Components
© 2006 CTS Corporation. All rights reserved. Information subject to change.
www.ctscorp.com
10/15/06
Help: 2013 National Electronic Design Competition K
[i=s]This post was last edited by paulhyde on 2014-9-15 03:19[/i] I chose this question this time, but I couldn't even measure the signal of the line. It can be said that I lost the whole game. The co...
qq380590456 Electronics Design Contest
Ask about the problem of PLL lock
I am using TI's cdcm7005 clock synchronizer. By configuring the parameters, I can get the lock signal, but this signal is sometimes high and sometimes low, that is, it is locked for a while, then unlo...
huihen330 Embedded System
Are there any PCB designers out there? I need support for the PCB design of a project.
Are there any PCB designers out there? I need support for the PCB design of a project....
歌坛杀手 PCB Design
How to design the simulation interface, Jtag or SW?
I want to make a board, using the F4 series, and use Jtag or SW for the simulation interface?Just ask the experts for advice!...
Dunn stm32/stm8
AD09 How to define the line name of the PCB library
As shown in the figure, the line cannot be named, and an error will be reported after importing the PCB, because there is no network when it is imported without a name....
675452482 PCB Design
0
Earn points and gain good luck[color=#FFFFFF]Thank you, the cleaner and the big rabbit[/color]...
weipingid Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 820  2280  2382  1252  2500  17  46  48  26  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号