LPW049-1228-07CB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> LPW049-1228-07CB95

LPW049-1228-07CB95: DescriptionIC Socket, BGA49, 49 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

LPW049-1228-07CB95 Overview

IC Socket, BGA49, 49 Contact(s), ROHS COMPLIANT

LPW049-1228-07CB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Actel
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA49
Shell material	PLASTIC
JESD-609 code	e4/e3
Manufacturer's serial number	LPW
Number of contacts	49
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Simple AC/DC indicator circuit diagram

AM amplitude modulation signal demodulator circuit diagram

Floor lamp power saving control circuit

DTMF VHF coding circuit

Pool water full drainage control circuit

Beautiful ESP32 Pacman Clock: Beautiful and interesting ESP32 Pacman clockhttps://www.instructables.com/ESP32-Pacman-Clock/...; dcexpert DIY/Open Source Hardware

[Learn Power Supply from TI] Series---TI female senior engineer explains how to achieve accurate current limiting in supercapacitor applications: How do you limit the charging current of a supercapacitor? TI applications engineer Amy Le walks you through a block diagram, provides sample calculations, and demonstrates how to accurately limit the...; qwqwqw2088 Analogue and Mixed Signal

MSP430FR5739 learning step by step: C language hello world program: Thanks to EEWORLD 's group purchase, everyone can experience TI 's new products at a low price. The board arrived on November 23 , but due to my busy work schedule and limited spare time, my learning ...; lcofjp Microcontroller MCU

21 detailed and superb analog electronics technical questions and answers: [color=red][b]First look at the directory Then look at question 1If you are satisfied, just download it[/b][/color][color=black] [color=darkred] [/color] [/color]...; qwqwqw2088 Analogue and Mixed Signal

The mc55 module automatically shuts down after 20 seconds of power on: After setting the mc55 module/IGT pin to a low level, the mc55 module is powered on, but after 20 seconds the mc55 module automatically shuts down. This happens every time, and I can't find the reason...; zj168 Embedded System

Interference caused by MSP430 sampling: The circuit I designed is a 10K square wave signal which is filtered by MAX275 to become a regular sinusoidal signal, and then directly enters MSP430 for sampling. But as soon as it is sampled by the ...; jcsasm Microcontroller MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components