ZCS1-120
WATER RESISTANT SOLENOID
FEATURES
•
Water resistant
•
Capable of handling low and high current requirements
•
Versatile mounting and termination
ORDERING INFORMATION
ZCS1-120
1
A
2
1
3
DC6V C 1 1 1
4
5 6 7 8
1. Part number:
ZCS1-120
2. Contact arrangement:
A: 1A (SPNO)
3. Coil termination
(15in - lb torque spec.)
1. Isolated w/#10-32 terminal (0.22 min. length)
2: Grounded w/#10-32 terminal (0.22 min. length)
3: Isolated w/1/4” Q.C terminal
4: Grounded w/1/4” Q.C terminal
6: Grounded w/#8-32 tapered terminal
7: iSOLATED w/#10-32 terminal (0.45 min. length)
8: Grounded w/#10-32 terminal (0.45 min. length)
4. Coil Voltage:
6,12,14,15, 24, 36, 48
5. Coil Type:
C: Continuous
I: Intermittent
6. Contact Material and termination (55 in-lb torque spec.):
1: AgCdO with 5/16” -24 terminal (0.38” min. length)
3: Cu with 5/16” -24 terminal (0.38” min. length)
4: Cu with 1/4” -20 terminal (0.50” min length
5: AgCdO with 5/16” -24 terminal (0.50” min. length)
7. Mounting Bracket:
1: Standard
2: “L” shaped bracket
8. Factory Assigned Special's:
(where undefined contact factory)
1: Without hardware
2: Extra hardware loosely mounted to solenoid
5: Zinc plated mounting bracket
7: No hardware, zinc plated mounting bracket
COIL PARAMETERS
•
Termination; #8 -32 UNC 2A, #10-32 UNF-2A thread or 1/4” quick
connect
•
Connections:
1. Coil isolated (two terminals)
2. One coil lead grounded to bracket (one terminal)
•
Coil data:
Coil
Voltage (VDC)
Rated
6
12
14
15
24
36
48
Max
6.6
13.2
15.4
16.5
26.4
39.6
52.8
Coil
Resistance (ohm)
Int.
*
6.0
*
9.4
24.0
54.0
*
Cont.
4.0
16.0
26.0
23.0
64.0
160.0
256.0
Must-Operate
Voltage (VDC)
Int.
*
8.04
*
10.05
16.08
24.12
*
Cont.
4.5
9.0
10.5
11.3
18.0
27.0
26.0
Coil
Power (W)
Int.
Cont.
24.0
9.0
*Special coils available upon request
CONTACT DATA
•
Contact Arrangement: 1A (SPNO)
•
Contact Material: AgCd0, or Copper
•
Termination; 5/16” -24 UNF-2A thread or 1/4” -20 UNC-2A thread
Load Voltage
(VDC)
12
12
36
*Number of operations
Ratings
Cont. (A)
80
100
100
In-rush (A)
400
400
400
Elec. Life Contact Material
10000*
50,000*
25,000*
Copper
AgCdO
AgCdO
10/11/06
ZCS1-120
GENERAL DATA
Dielelectric Strength
Temperature Range
Mechanical Life (no load)
Mounting position (Recommended)
Duty Cycle
500 Volts
-20°F~150°F (-28.9°C~65.6°C) - Intermittent
-20°F~120°F (-28.9°C~48.9°C) - Continuous
250,000 cycles
Plunger vertical with cap down
Continuous; Intermittent: 10sec "on"
maximum and minimum 60sec "off".
60sec "on" max and minimum 6min "off."
44-55 in*lbs (Contact terminal);
12-18 in*lbs (Coil terminal)
170.5 grams
Hardward Torque specification
Weight
MECHANICAL DATA
3.253
2 - 0.281X0.400
0.375
1.375
5“ 2.4 UNF- 2A
4
16 THREAD TYP
2.125
2.875
0.625
Cap / Plunger
#10 -
32
UNF -2A
THREAD TYPE
Dimensions
and
Mounting
Dimensions
and
for
Standard
Bracket
Mounting
Wiring diagram
APPLICATION NOTES:
1.) Not all number combinations are available. Please contact your Sales Representative for available
part numbers.
2.) Solenoid applied in battery charging circuits should be protected from higher than rated voltage during charging.
The service life may be affected by this condition and the solenoid may or may not operate the circuit as intended.
3.) Circuits should be designed to provide safe operation should the solenoid fail in either the open or closed position.
4.) A back-up wrench must be used to hold the bottom nut stationary during installation.
2.125
10/11/06
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
