EEWORLDEEWORLDEEWORLD

Part Number

Search

A3144-U

Description
MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
Categorysemiconductor    Other integrated circuit (IC)   
File Size142KB,8 Pages
ManufacturerAllegro
Websitehttp://www.allegromicro.com/
Download Datasheet View All

A3144-U Overview

MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER

3141
THRU
3144
SENSITIVE HALL-EFFECT SWITCHES
FOR HIGH-TEMPERATURE OPERATION
These Hall-effect switches are monolithic integrated circuits with
tighter magnetic specifications, designed to operate continuously over
extended temperatures to +150°C, and are more stable with both
temperature and supply voltage changes. The unipolar switching
characteristic makes these devices ideal for use with a simple bar or rod
magnet. The four basic devices (3141, 3142, 3143, and 3144) are
identical except for magnetic switch points.
Each device includes a voltage regulator for operation with supply
voltages of 4.5 to 24 volts, reverse battery protection diode, quadratic
Hall-voltage generator, temperature compensation circuitry, small-
signal amplifier, Schmitt trigger, and an open-collector output to sink
up to 25 mA. With suitable output pull up, they can be used with
bipolar or CMOS logic circuits. The A3141– and A3142– are im-
proved replacements for the UGN/UGS3140–; the A3144– is the
improved replacement for the UGN/UGS3120–.
The first character of the part number suffix determines the device
operating temperature range. Suffix ‘E–’ is for the automotive and
industrial temperature range of -40°C to +85°C. Suffix ‘L–’ is for the
automotive and military temperature range of -40°C to +150°C. Three
package styles provide a magnetically optimized package for most
applications. Suffix ‘–LT’ is a miniature SOT89/TO-243AA transistor
package for surface-mount applications; suffix ‘–UA’ is a three-lead
ultra-mini-SIP.
Data Sheet
27621.6B*
V
X
CC
1
2
3
GROUND
Dwg. PH-003A
Pinning is shown viewed from branded side.
OUTPUT
SUPPLY
FEATURES and BENEFITS
ABSOLUTE MAXIMUM RATINGS
at T
A
= +25
°
C
Supply Voltage, V
CC
............................
28 V
Reverse Battery Voltage, V
RCC
...........
-35 V
Magnetic Flux Density, B ..........
Unlimited
Output OFF Voltage, V
OUT
..................
28 V
Reverse Output Voltage, V
OUT
...........
-0.5 V
Continuous Output Current, I
OUT
......
25 mA
Operating Temperature Range, T
A
Suffix ‘E–’ ..................
-40
°
C to +85
°
C
Suffix ‘L–’ ................
-40
°
C to +150
°
C
Storage Temperature Range,
T
S
..............................
-65
°
C to +170
°
C
s
s
s
s
s
s
s
s
Superior Temp. Stability for Automotive or Industrial Applications
4.5 V to 24 V Operation … Needs Only An Unregulated Supply
Open-Collector 25 mA Output … Compatible with Digital Logic
Reverse Battery Protection
Activate with Small, Commercially Available Permanent Magnets
Solid-State Reliability
Small Size
Resistant to Physical Stress
Always order by complete part number, e.g.,
A3141ELT
.
What is the capacitance of the chip capacitor 3452?
My hard drive is broken. It is not recognized. I removed the hard drive and found a capacitor, marked with a horizontal line with 34 below and 52 below. I posted this using another machine. I would li...
ddllxxrr Analog electronics
Cadence Allegro Practical Strategy and High-Speed PCB Design
This book is based on OrCAD and Allegro in the currently stable SPB 16.6 version of Cadence, and introduces in detail the methods and techniques of using SPB 16.6 to implement schematics and high-spee...
arui1999 Download Centre
Image Algorithm Transplantation to DSP and Its Optimization Steps
When you need to transplant the algorithm you have written to the DSP development board and run it well, what work needs to be done? The following is divided into two parts. The first part is transpla...
fish001 Microcontroller MCU
89C2051 MCU P1 driver encounters strange phenomenon? Would you like to ask an expert for advice?
Recently, I used 89C2051 to drive CCD, and the crystal oscillator used was 12M, mainly to control the timing of P10, P11, and P12. I needed to assign values to P10, P11, and P12 continuously, and assi...
njgwx 51mcu
Question about KEIL 4 hardware emulation
I followed the KEIL 2 tutorial. My COM port is COM5. I checked it on the computer and it is definitely correct. Then I set the crystal oscillator to 11.0592 and the baud rate to 38400. Why can't I con...
zzbeagle Integrated technical exchanges
Share some good things I saw in deyisupport
[align=left][url=http://www.deyisupport.com/blog/b/thinkinnovative/archive/2015/04/24/51951.aspx][font=微软雅黑][size=3]Use tactile feedback to simulate the feeling of touch[/size][/font][/url][/align][al...
eric_wang TI Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1760  2810  2102  650  2104  36  57  43  14  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号