EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63114-530L

Description
Line Driver, 1 Driver, Hybrid, CDFP24
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63114-530L Overview

Line Driver, 1 Driver, Hybrid, CDFP24

BUS-63114-530L Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
package instructionDFP, FL24,1.3,100
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives1
Interface integrated circuit typeLINE DRIVER
JESD-30 codeR-XDFP-F24
JESD-609 codee0
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Minimum output swing29 V
Package body materialCERAMIC
encapsulated codeDFP
Encapsulate equivalent codeFL24,1.3,100
Package shapeRECTANGULAR
Package formFLATPACK
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply5,+-12/+-15 V
Certification statusNot Qualified
Maximum receive delay
Filter level38535V;38534K;883S
surface mountYES
technologyHYBRID
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Base Number Matches1
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
EEWORLD University Hall----Type C mobile power design with input and output fast charging mode
Type C mobile power design with input and output fast charging : https://training.eeworld.com.cn/course/3688...
hi5 Power technology
Who has used ADS? How to import PADS PCB into ADS?
Has anyone used ADS? How do I import a PCB from PADS into ADS? Any advice or information is welcome. Thanks in advance!...
kata PCB Design
The output voltage of the STM32 IO port is about 3.3V, but it cannot drive the motor? ?
Recently, I have been using the output level of the STM32 IO port to input the input of the L298N, and then used it to drive the motor. However, I don’t know why the output voltage of the L298N is alw...
wubaobao1993 stm32/stm8
How Active and Passive Cell Balancing Work
In the Power System Design article, “Active and Passive Balancing of Battery Management Systems,” Stefano Zanella describes how multi-cell systems can become unbalanced. In this article, I want to exp...
okhxyyo Analogue and Mixed Signal
Problems with Wince6.0 R3 system customization
为什么Run-time image can be larger than 32MB(IMGRAM64=1)选中后还会出现如下信息,nk.bin生成不了 Pass 1...Warning: Unable to do imports from ppp.dll to RSAENH.dll - will late bind Warning: Unable to do imports from schann...
woshis Embedded System
How do transistors drive dot matrix?
The base cannot drive the dot matrix whether there is a voltage level or not? Also, can the transistor be turned on without wiring?...
wrlsohu 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1866  696  2395  1949  795  38  14  49  40  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号