MCP6566/6R/6U/7/9
1.8V Low Power Open-Drain Output Comparator
Features
• Propagation Delay at 1.8V
DD
:
- 56 ns (typical) High to Low
• Low Quiescent Current: 100 µA (typical)
• Input Offset Voltage: ±3 mV (typical)
• Rail-to-Rail Input: V
SS
- 0.3V to V
DD
+ 0.3V
• Open-Drain Output
• Wide Supply Voltage Range: 1.8V to 5.5V
• Available in Single, Dual, and Quad
• Packages: SC70, SOT-23-5, SOIC, MSOP,
TSSOP
Description
The Microchip Technology, Inc. MCP6566/6R/6U/7/9
families of Open-Drain output comparators are offered
in single, dual and quad configurations.
These comparators are optimized for low power 1.8V,
single-supply applications with greater than rail-to-rail
input operation. The internal input hysteresis eliminates
output switching due to internal input noise voltage,
reducing current draw. The open-drain output of the
MCP6566/6R/6U/7/9 family requires a pull up resistor
and it supports pull-up voltages above and below V
DD
which can be used to level shift. The output toggle
frequency can reach a typical of 4 MHz (typical) while
limiting supply current surges and dynamic power
consumption during switching.
This family operates with single supply voltage of 1.8V
to 5.5V while drawing less than 100 µA/comparator of
quiescent current (typical).
Typical Applications
•
•
•
•
•
•
•
Laptop computers
Mobile Phones
Hand-held Electronics
RC Timers
Alarm and Monitoring Circuits
Window Comparators
Multi-vibrators
Package Types
MCP6566
SOT-23-5, SC70-5
OUT
1
V
SS
2
+IN
3
MCP6568
SOIC, MSOP
8
V
DD
- +
+ -
Design Aids
• Microchip Advanced Part Selector (MAPS)
• Analog Demostration and Evaluation Boards
• Application Notes
5
V
DD
OUTA
1
-INA
2
4
-IN
7
OUTB
6
-INB
5
+INB
MCP6566R
SOT-23-5
OUT
1
V
DD
2
+IN
3
5
V
SS
+
-
+
-
+INA
3
V
SS
4
MCP6569
SOIC, TSSOP
OUTA
1
-INA
2
+INA
3
V
DD
4
+INB
5
-INB
6
- +
+ -
- +
+ -
Related Device
• Push-Pull Output: MCP6561/1R/1U/2/4
14
OUTD
13
-IND
12
+IND
11
V
SS
10 +INC
9
-INC
8
OUTC
Typical Application
+3V
PU
V
IN
V
DD
R
2
R
F
+5V
DD
V
OUT
MCP656X
4
-IN
MCP6566U
SOT-23-5
+
-
V
IN
+ 1
V
SS
2
V
IN
– 3
5 V
DD
OUTB
7
4 OUT
R
3
©
2009 Microchip Technology Inc.
DS22143B-page 1
MCP6566/6R/6U/7/9
NOTES:
DS22143B-page 2
©
2009 Microchip Technology Inc.
MCP6566/6R/6U/7/9
1.0
1.1
ELECTRICAL
CHARACTERISTICS
Maximum Ratings*
V
DD
- V
SS
....................................................................... 6.5V
Open-Drain Output.............................................V
SS
+ 10.5V
All other inputs and outputs...........V
SS
– 0.3V to V
DD
+ 0.3V
Difference Input voltage ......................................|V
DD
- V
SS
|
Output Short Circuit Current .................................... ±25 mA
Current at Input Pins .................................................. ±2 mA
Current at Output and Supply Pins .......................... ±50 mA
Storage temperature ................................... -65°C to +150°C
Ambient temp. with power applied .............. -40°C to +125°C
Junction temp............................................................ +150°C
ESD protection on all pins (HBM/MM)
.................≥
4 kV/300V
*Notice:
Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
DC CHARACTERISTICS
Electrical Characteristics:
Unless otherwise indicated: V
DD
= +1.8V to +5.5V, V
SS
= GND, T
A
= +25°C, V
IN
+ = V
DD
/2, V
IN
- = V
SS
,
and R
Pull-Up
= 20 kΩ to V
PU
= V
DD
(see
Figure 1-1).
Parameters
Power Supply
Supply Voltage
Quiescent Current per comparator
Power Supply Rejection Ratio
Input
Input Offset Voltage
Input Offset Drift
Input Offset Current
Input Bias Current
V
OS
ΔV
OS
/ΔT
I
OS
I
B
-10
—
—
—
—
—
Input Hysteresis Voltage
Input Hysteresis Linear Temp. Co.
Input Hysteresis Quadratic Temp. Co.
Common-Mode Input Voltage Range
Common-Mode Rejection Ratio
V
HYST
TC
1
TC
2
V
CMR
CMRR
1.0
—
—
V
SS
−0.2
V
SS
−0.3
54
50
54
Common Mode Input Impedance
Differential Input Impedance
Note 1:
2:
3:
4:
Z
CM
Z
DIFF
—
—
V
DD
I
Q
PSRR
1.8
60
63
—
100
70
5.5
130
—
+10
—
—
—
—
5000
5.0
—
—
V
DD
+0.2
V
DD
+0.3
—
—
—
—
—
V
µA
dB
mV
µV/°C
pA
pA
pA
pA
mV
µV/°C
µV/°C
2
V
V
dB
dB
dB
Ω||pF
Ω||pF
V
DD
= 1.8V
V
DD
= 5.5V
V
CM
= -0.3V to V
DD
+0.3V, V
DD
= 5.5V
V
CM
= V
DD
/2 to V
DD
+0.3V, V
DD
= 5.5V
V
CM
= -0.3V to V
DD
/2, V
DD
= 5.5V
I
OUT
= 0
V
CM
= V
SS
V
CM
= V
SS
(Note 1)
V
CM
= V
SS
V
CM
= V
SS
T
A
= +25°C, V
IN
- = V
DD
/2
T
A
= +85°C, V
IN
- = V
DD
/2
T
A
= +125°C, V
IN
- = V
DD
/2
V
CM
= V
SS
(Notes 1, 2)
Symbol
Min
Typ
Max
Units
Conditions
±
3
±
2
±
1
1
60
1500
—
10
0.3
—
—
66
63
65
10 ||4
10 ||2
13
13
The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the
input-referred trip points.
V
HYST
at different temperatures is estimated using V
HYST
(T
A
) = V
HYST @ +25°C
+ (T
A
- 25°C) TC
1
+ (T
A
- 25°C)
2
TC
2
.
Limit the output current to Absolute Maximum Rating of 50 mA.
The pull up voltage for the open drain output V
PULL_UP
can be as high as the absolute maximum rating of 10.5V. In this
case, I
OH_leak
can be higher than 1 µA (see
Figure 2-30).
©
2009 Microchip Technology Inc.
DS22143B-page 3
MCP6566/6R/6U/7/9
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics:
Unless otherwise indicated: V
DD
= +1.8V to +5.5V, V
SS
= GND, T
A
= +25°C, V
IN
+ = V
DD
/2, V
IN
- = V
SS
,
and R
Pull-Up
= 20 kΩ to V
PU
= V
DD
(see
Figure 1-1).
Parameters
Push-Pull Output
Pull-up Voltage
High Level Output Voltage
High Level Output Current leakage
Low Level Output Voltage
Short Circuit Current
(Notes 3)
Output Pin Capacitance
Note 1:
2:
3:
4:
V
PULL_UP
V
OH
I
OH_leak
V
OL
I
SC
C
OUT
1.6
—
—
—
—
—
—
—
—
—
±30
8
5.5
V
PULL_UP
1
0.6
—
—
V
V
µA
V
mA
pF
(see
Figure 1-1)
(Notes 3, 4)
Note 4
I
OUT
= 3 mA/8 mA @ V
DD
= 1.8V/5.5V
Not to exceed Absolute Max. Rating
Symbol
Min
Typ
Max
Units
Conditions
The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the
input-referred trip points.
V
HYST
at different temperatures is estimated using V
HYST
(T
A
) = V
HYST @ +25°C
+ (T
A
- 25°C) TC
1
+ (T
A
- 25°C)
2
TC
2
.
Limit the output current to Absolute Maximum Rating of 50 mA.
The pull up voltage for the open drain output V
PULL_UP
can be as high as the absolute maximum rating of 10.5V. In this
case, I
OH_leak
can be higher than 1 µA (see
Figure 2-30).
AC CHARACTERISTICS
Electrical Characteristics:
Unless otherwise indicated,: Unless otherwise indicated,: V
DD
= +1.8V to +5.5V, V
SS
= GND,
T
A
= +25°C, V
IN+
= V
DD
/2, V
IN-
= V
SS
, R
Pull-Up
= 20 kΩ to V
PU
= V
DD
, and C
L
= 25 pf (see
Figure 1-1).
Parameters
Propagation Delay
High-to-Low,100 mV Overdrive
Output
Fall Time
Maximum Toggle Frequency
Input Voltage Noise
Note 1:
2:
t
F
f
TG
E
NI
—
—
—
—
20
4
2
350
—
—
—
—
ns
MHz
MHz
µV
P
-
P
V
DD
= 5.5V
V
DD
= 1.8V
10 Hz to 10 MHz
(Note 1)
t
PHL
—
—
56
34
80
80
ns
ns
V
CM
= V
DD
/2, V
DD
= 1.8V
V
CM
= V
DD
/2, V
DD
= 5.5V
Symbo
l
Min
Typ
Max
Units
Conditions
ENI is based on SPICE simulation.
Rise time t
R
and t
PLH
depend on the load (R
L
and C
L
). These specification are valid for the specified load only.
TEMPERATURE SPECIFICATIONS
Electrical Characteristics:
Unless otherwise indicated: V
DD
= +1.8V to +5.5V and V
SS
= GND.
Parameters
Temperature Ranges
Specified Temperature Range
Operating Temperature Range
Storage Temperature Range
Thermal Package Resistances
Thermal Resistance, SC70-5
Thermal Resistance, SOT-23-5
Thermal Resistance, 8L-MSOP
Thermal Resistance, 8L-SOIC
Thermal Resistance, 14L-SOIC
Thermal Resistance, 14L-TSSOP
θ
JA
θ
JA
θ
JA
θ
JA
θ
JA
θ
JA
—
—
—
—
—
—
331
220.7
211
149.5
95.3
100
—
—
—
—
—
—
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
T
A
T
A
T
A
-40
-40
-65
—
—
—
+125
+125
+150
°C
°C
°C
Symbo
l
Min
Typ
Max
Units
Conditions
DS22143B-page 4
©
2009 Microchip Technology Inc.
MCP6566/6R/6U/7/9
1.2
Test Circuit Configuration
This test circuit configuration is used to determine the
AC and DC specifications.
V
DD
MCP656X
V
PU
= V
DD
I
OUT
R
PU
20 kΩ
V
OUT
25 pF
V
SS
= 0V
200 kΩ
200 kΩ
V
IN
= V
SS
FIGURE 1-1:
AC and DC Test Circuit for
the Open-Drain Output Comparators.
©
2009 Microchip Technology Inc.
DS22143B-page 5
京公网安备 11010802033920号
EEWORLD
