EEWORLDEEWORLDEEWORLD

Part Number

Search

8D0-13ZC35PE022

Description
MIL Series Connector, 22 Contact(s), Aluminum Alloy, Male, Crimp Terminal, Receptacle,
CategoryThe connector    The connector   
File Size692KB,12 Pages
ManufacturerEsterline Technologies Corporation
Download Datasheet Parametric View All

8D0-13ZC35PE022 Overview

MIL Series Connector, 22 Contact(s), Aluminum Alloy, Male, Crimp Terminal, Receptacle,

8D0-13ZC35PE022 Parametric

Parameter NameAttribute value
MakerEsterline Technologies Corporation
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresSTANDARD: MIL-DTL-38999, EMI SHIELDED, POLARIZED
Back shell typeSOLID
Body/casing typeRECEPTACLE
Connector typeMIL SERIES CONNECTOR
Contact to complete cooperationGOLD OVER NICKEL
Contact completed and terminatedGOLD OVER NICKEL
Contact point genderMALE
Coupling typeTHREADED
DIN complianceNO
empty shellNO
Environmental characteristicsENVIRONMENT/FLUID RESISTANT
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceYES
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE AND PANEL
OptionsGENERAL PURPOSE
Shell surfaceGREEN ZINC COBALT PLATED
Shell materialALUMINUM ALLOY
Housing size13
Termination typeCRIMP
Total number of contacts22
Base Number Matches1
8D Series
D38999 Aluminum Series
Connector part numbers
Basic Series
8D
0
-
1
1
W
35
P
N
Shell style:
0:
Square flange receptacle
1:
In line receptacle
7:
Jam nut receptacle
5: Plug with RFI shielding
Also available:
.
Square flange receptacle with clinch nuts (see page 80)
.
Jam nut receptacle with double flange (see page 83)
Type:
None:
Connectors with standard crimp contacts.
L: Receptacle with long PC tail (male and female size #22D, #20).
C: Receptacle with short PC tail (male and female #22D, #20, #16).
S: Receptacle with specific PC tail (male et female #22D)
W: Receptacle with male contacts #22D for wire wrap (3 wraps)
T:
Receptacle with male contacts #20 for wire wrap (2 wraps)
P:
Receptacle with solder cup - only available for Reinforced sealing Series (see
page 75) - male and female size #22D; male #16 & #1
2; female #16 & #1
2
and male female #20 please consult us
Shell size: 09, 1 , 1 15, 1 1 21 23, 25
1 3,
7, 9, ,
Plating:
W:
Olive drab cadmium
F: Nickel
ZC:
Green zinc cobalt
Z: Black zinc nickel
Contact layout:
See pages 1 to 16
3
Contact type:
P:
Pin
A:
Connector supplied less pin contact or with specific contacts (connector marking: A + orientation)
S:
Socket
B:
Connector supplied less socket contact or with specific contacts (connector marking: B + orientation)
Orientation: N, A, B, C, D, E
(see page 64)
Specification:
046:
Tinned straight PC tail
251:
Connector provided with power contacts (layouts with contact #8)
022: Fuel tank
Special custom:
None:
Standard plastic cap
M:
Antistatic plastic cap
L: For P or S contact type only, connectors delivered without contacts, connectors marking P or S plus orientation
-
-
L
22
[CoreUtil/General]: Illegal State
IAR compilation error code  Internal Error: [CoreUtil/General]: Illegal StateHas anyone encountered the same problem?...
ykyyky Microcontroller MCU
CC6.1 compile and generate Hex problem
When Enable ARM Hex Utility is not selected, no warning appears during compilation, Debug can run, and the program logic is correct. However, after selecting Enable ARM Hex Utility, multiple warnings ...
kkmugs Microcontroller MCU
Design: Overvoltage protection high-side switch with only four devices
Although MCUs typically run at a low voltage of 3.3V, there are often situations where they need to control a load at a high voltage of 12V. If the MCU cannot be controlled by a low-side switch, a met...
超级电工 MCU
Stories about people being cheated by various housekeepers/antivirus software
Today, someone in the water group called me and said that his cadence was down, and he didn't know why. I suggested to him to check whether his security manager/antivirus software did something bad an...
okhxyyo Talking
How to perform mark verification on the serial port of stm32
Recently, I used mark check in serial communication. I checked and found that the check bit needs to be fixed to 1. I don't know how to set it so that the check bit can be fixed to 1? Experts, please ...
chenbingjy stm32/stm8
C51 calls the assembly program
You can learn...
njlianjian 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2517  232  90  2170  47  51  5  2  44  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号