Changes to Applications section................................................. 1
Changes to General Description ................................................ 1
Changes to Specifications ............................................................ 4
Changes to Timing Specifications .............................................. 5
Changes to Timing Example ..................................................... 19
9/03—Revision 0: Initial Version
Rev. B | Page 2 of 28
AD7452
AD7452–SPECIFICATIONS
V
DD
= 2.7 V to 3.6 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.0 V; V
DD
= 4.75 V to 5.25 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.5 V;
V
CM1
= V
REF
; T
A
= T
MIN
to T
MAX
, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Signal-to-(Noise + Distortion) (SINAD)
3
Total Harmonic Distortion (THD)
3
Peak Harmonic or Spurious Noise
3
Intermodulation Distortion (IMD)
3
Second-Order Terms
Third-Order Terms
Aperture Delay
3
Aperture Jitter
3
Full Power Bandwidth
3, 4
DC ACCURACY
Resolution
Integral Nonlinearity (INL)
3
Differential Nonlinearity (DNL)
3
Zero-Code Error
3
Positive Gain Error
3
Negative Gain Error
3
ANALOG INPUT
Full-Scale Input Span
Absolute Input Voltage
V
IN+
V
IN–
DC Leakage Current
Input Capacitance
REFERENCE INPUT
V
REF
Input Voltage
Test Conditions/Comments
f
IN
= 100 kHz
V
DD
= 4.75 V to 5.25 V, –86 dB typ
V
DD
= 2.7 V to 3.6 V, –84 dB typ
V
DD
= 4.75 V to 5.25 V, –86 dB typ
V
DD
= 2.7 V to 3.6 V, –84 dB typ
fa = 90 kHz, fb = 110 kHz
B Version
2
70
–76
–74
–76
–74
–89
–89
5
50
20
2.5
12
±1
± 0.95
±6
±2
±2
V
IN+
– V
IN–
V
CM1
± V
REF
/2
V
CM1
± V
REF
/2
±1
30/10
2.5
6
2.0
7
±1
10/30
2.4
0.8
±1
10
2.8
2.4
0.4
±1
10
Twos Complement
Unit
dB min
dB max
dB max
dB max
dB max
dB typ
dB typ
ns typ
ps typ
MHz typ
MHz typ
Bits
LSB max
LSB max
LSB max
LSB max
LSB max
V
V
V
µA max
pF typ
V
V
µA max
pF typ
V min
V max
µA max
pF max
V min
V min
V max
µA max
pF max
@ –3 dB
@ –0.1 dB
Guaranteed no missed codes to 12 bits
2 × V
REF 5
V
CM
= V
REF
V
CM
= V
REF
When in track/hold
V
DD
= 4.75 V to 5.25 V (±1% tolerance for
specified performance)
V
DD
= 2.7 V to 3.6 V (±1% tolerance for
specified performance)
When in track/hold
DC Leakage Current
V
REF
Input Capacitance
LOGIC INPUTS
Input High Voltage, V
INH
Input Low Voltage, V
INL
Input Current, I
IN
Input Capacitance, C
IN 8
LOGIC OUTPUTS
Output High Voltage, V
OH
Output Low Voltage, V
OL
Floating-State Leakage Current
Floating-State Output Capacitance
8
Output Coding
Typically 10 nA, V
IN
= 0 V or V
DD
V
DD
= 4.75 V to 5.25 V, I
SOURCE
= 200 µA
V
DD
= 2.7 V to 3.6 V, I
SOURCE
= 200 µA
I
SINK
= 200 µA
Rev. B | Page 3 of 28
AD7452
Parameter
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
3
Throughput Rate
POWER REQUIREMENTS
V
DD
I
DD9, 10
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
Power Dissipation
Normal Mode (Operational)
Full Power-Down
Test Conditions/Comments
1.6 µs with a 10 MHz SCLK
Sine wave input
Step input
B Version
2
16
200
290
555
Unit
SCLK cycles
ns max
ns max
kSPS max
Range: 3 V + 20%/–10%;
5 V ± 5%
SCLK on or off
V
DD
= 4.75 V to 5.25 V
V
DD
= 2.7 V to 3.6 V
SCLK on or off
V
DD
= 5 V, 1.55 mW typ for 100 kSPS
9
V
DD
= 3 V, 0.64 mW typ for 100 kSPS
9
V
DD
= 5 V, SCLK on or off
V
DD
= 3 V, SCLK on or off
2.7/5.25
0.5
1.5
1.2
1
7.25
3.3
5
3
V min/V max
mA typ
mA max
mA max
µA max
mW max
mW max
µW max
µW max
1
2
Common-mode voltage. The input signal can be centered on a dc common-mode voltage in the range specified in Figure 23 and Figure 24.
Temperature ranges as follows: B Version: –40°C to +85°C.
3
See Terminology section.
4
Analog inputs with slew rates exceeding 27 V/µs (full-scale input sine wave > 3.5 MHz) within the acquisition time may cause an incorrect result to be returned by the
converter.
5
Because the input spans of V
IN+
and V
IN–
are both V
REF
and are 180° out of phase, the differential voltage is 2 × V
REF.
6
The AD7452 is functional with a reference input from 100 mV; for V
DD
= 5 V, the reference can range up to 3.5 V.
7
The AD7452 is functional with a reference input from 100 mV; for V
DD
= 3 V, the reference can range up to 2.2 V.
8
Guaranteed by characterization.
9
See Power vs. Throughput Rate section.
10
Measured with a midscale dc input.
Rev. B | Page 4 of 28
AD7452
TIMING SPECIFICATIONS
Guaranteed by characterization. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
DD
) and timed from a 1.6 V voltage
level. See Figure 2 and the Serial Interface section.
V
DD
= 2.7 V to 3.6 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.0 V; V
DD
= 4.75 V to 5.25 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.5 V;
V
CM1
= V
REF
; T
A
= T
MIN
to T
MAX
, unless otherwise noted.
Table 2.
Parameter
f
SCLK 2
t
CONVERT
t
QUIET
t
1
t
2
t
33
t
43
t
5
t
6
t
7
t
8 4
t
POWER-UP5
Limit at T
MIN
, T
MAX
10
10
16 × t
SCLK
1.6
60
10
10
20
40
0.4 t
SCLK
0.4 t
SCLK
10
10
35
1
Unit
kHz min
MHz max
µs max
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns max
µs max
Description
t
SCLK
= 1/f
SCLK
Minimum quiet time between the end of a serial read and the next falling edge of CS
Minimum CS pulse width
CS falling edge to SCLK falling edge setup time
Delay from CS falling edge until SDATA three-state disabled
Data access time after SCLK falling edge
SCLK high pulse width
SCLK low pulse width
SCLK edge to data valid hold time
SCLK falling edge to SDATA three-state enabled
SCLK falling edge to SDATA three-state enabled
Power-up time from full power-down
t
1
CS
t
2
SCLK
1
2
3
4
t
5
5
t
CONVERT
B
13
14
15
16
SDATA
0
0
0
4 LEADING ZEROS
0
DB11
DB10
DB2
DB1
DB0
t
QUIET
THREE-STATE
Figure 2. Serial Interface Timing Diagram
1
2
Common-mode voltage.
Mark/space ratio for the SCLK input is 40/60 to 60/40.
3
Measured with the load circuit of Figure 3 and defined as the time required for the output to cross 0.8 V or 2.4 V with V
DD
= 5 V, or 0.4 V or 2.0 V for V
DD
= 3 V.
4
t
8
is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 3. The measured number is then extrapolated
back to remove the effects of charging or discharging the 25 pF capacitor. This means that the time, t
8
, quoted in the Timing Specifications is the true bus relinquish
time of the part and is independent of the bus loading.
In the field of signal measurement, small signals must be conditioned by circuits, generally including amplification, filtering, frequency division, etc. For signal filtering circuits, a signal genera...
Can port mapping map multiplexed pins? For example, uart1 is already multiplexed pins 8.2 and 8.3. Can these two pins be mapped to P2.2 and 2.3? Let's discuss this....
[table=95%][tr][td]I have learned the theoretical knowledge of DSP, such as FFT algorithm and digital filter theory. I have also developed a lot of single-chip microcomputers. How long does it take to...
The hardware circuit design of a single-chip microcomputer application system includes two parts: one is system expansion, that is, when the functional units inside the single-chip microcomputer, such...
1. Common CAN features Compatible with CAN specification 2.0B, ISO11898-1; [/align][align=left] Multi-master structure with non-destructive bit arbitration; [/align][align=left] Bus access priority co...
1. I have installed freeradius in a virtual machine on one computer and used it as a radius server. 2. I want to install a radius client in a virtual machine on another computer to implement simple us...
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Spatial Division Multiplexing (SDM) MIMO processing can significantly improve spectrum efficiency and thus greatly increase the capacity of wireless communication systems. Spatial Division Multip...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
LED light sources have many environmental advantages, but early products still have certain technical bottlenecks in heat dissipation and high brightness design that cannot be broken through....[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
In order to prevent the lithium battery from being damaged by abnormal conditions such as overcharge, over discharge, and overcurrent, a lithium battery protection device is usually used to prevent...[Details]
Currently, high-frequency and high-efficiency DCDC converters are increasingly used in automotive electronic systems.
High switching frequency can use smaller power inductors and output filter...[Details]
Based on the actual situation, a remote intelligent anti-theft alarm device for home use, connected to the telephone line, simple to operate, and stable and reliable in operation is designed. When ...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
