DS1668, DS1669, DS1669S
Dallastat
TM
DS1668, DS1669, DS1669S
Electronic Digital Rheostat
FEATURES
PIN ASSIGNMENT DS1669
(R
H
)
UC
D
(R
L
)
1
2
3
4
8
7
6
5
+V
DC
R
W
–V
•
Replaces mechanical variable resistors
•
Available as the DS1668 with manual interface or the
DS1669 integrated circuit
•
Human
engineered interface provides easy control
with DS1668
interface provided for digital as well as
manual control
•
Electronic
8-Pin DIP (300 Mil)
See Mech. Drawings
Section
•
Wide differential input voltage range between 4.5 and
8 volts
(R
H
)
UC
D
(R
L
)
1
2
3
4
8
7
6
5
+V
DC
R
W
V-
•
Wiper position is maintained in the absence of power
•
Low cost alternative to mechanical controls
•
Applications
include volume, tone, contrast, bright-
ness, and dimmer control
R
H
R
W
R
L
-V, +V
UC
D
DC
8-Pin SOIC (208 Mil)
See Mech. Drawings
Section
•
8–pin SOIC and 8–pin DIP packages for DS1669
•
Standard resistance values for Dallastat
– DS1668/DS1669–10
~
10KΩ
– DS1668/DS1669–50
~
50KΩ
– DS1668/DS1669–100
~
100KΩ
PIN DESCRIPTION DS1669
-
-
-
-
-
-
-
Resistor High End
Resistor Wiper
Resistor Low End
Voltage Inputs
Up Contact Input
Digital Input
Down Contact Input
•
Operating Temperature Range
– Commercial: 0°C to 70°C; DS1668, DS1669
– Industrial: –40°C to +85°C; DS1669
PIN DESCRIPTION DS1668
PIN ASSIGNMENT DS1668
R
H
NC D
6
PIN 1
INDICATOR
1
2
3
5
4
TOP VIEW
+V
-V
R
W
D
R
H
NC
-
-
-
-
-
-
Positive Voltage Input
Negative Voltage
Resistor Wiper
Digital Input
Resistor High End
No Connection - Pin Missing
+V R
W
-V
INTEGRATED
PUSHBUTTON
022698 1/10
DS1668, DS1669, DS1669S
DESCRIPTION
The DS1668 and DS1669 Dallastats are digital rheo-
stats or potentiometers. These units provide 64 pos-
sible uniform tap points over the resistive range and are
available in standard versions of 10K, 50K, and 100K
ohms. The Dallastats can be controlled by either a
mechanical–type contact closure input or a digital
source input such as a CPU. Wiper position is main-
tained in the absence of power which is accomplished
through the use of a EEPROM memory cell array. The
EEPROM cell array is specified to accept greater than
80,000 writes.
The DS1668 and DS1669 differ in the type packages in
which they are offered. The DS1668 is only available in
a custom 6–pin package with a single integrated push-
button as shown in the package drawing. The single
integrated pushbutton provides the mechanical control
input of the wiper position. In addition, a digital source
input, D, allows the potentiometer to be controlled by a
microcontroller or processor. Other package pins
include the positive voltage input, +V, the negative volt-
age input, –V, the resistor wiper terminal, R
W
, and the
high resistor terminal, R
H
. The DS1668 is rated for com-
mercial temperature usage only (0°C to 70°C).
The DS1669 is offered in two standard IC packages
which include an 8–pin 300 mil DIP and an 8–pin 200 mil
SOIC. Like the DS1668, the DS1669 can be configured
to operate using a single pushbutton or digital source
input. This is illustrated in Figure 1. Additionally, the
DS1669 can be configured to operate in a dual pushbut-
ton configuration which is shown in Figure 2. The
DS1669 pinouts allow access to both ends of the poten-
tiometer R
L
, R
H
, and the wiper, R
W
. Control inputs
include the digital source input, D, the up contact input,
UC, and the down contact input, DC. Other package
pinouts include the positive,+V, and negative, –V , sup-
ply inputs. The DS1669 is available in commercial or
industrial temperature versions.
Figure 3 illustrates the single pushbutton configuration
of the DS1668. Internally, the low end resistor terminal
is connected to the negative supply input terminal. The
integrated pushbutton has one side connected to the
negative supply input while the other side is connected
to the up contact terminal (UC). The digital source input
(D) is accessible through pin 4 of the package. The (D)
input has an internal pull–up resistor and can be allowed
to float when not in use. The down contact input (DC) is
not accessible externally. However, this control input is
internally connected to the positive input supply.
When powered, the DS1668 assumes a single pushbut-
ton mode of operation. Pressure applied to the inte-
grated pushbutton will cause contact closure which in
turn will move the wiper position upward or downward
depending on the previous wiper direction. Single push-
button mode is accomplished in the same manner for
the DS1669. However, for the DS1669, all connections
must be made by the user since no internal connections
exist (see Figure 1). Note that single pushbutton control
is accomplished when 1) the (DC) input is connected to
the positive supply input and 2) the (D) input is allowed
to float. These two conditions must exist from the time of
device power–up. The UC input controls both upward
and downward movement of the device wiper position in
single pushbutton mode of operation.
Dual pushbutton operation is only available when using
the DS1669. The DS1668, by design, only supports the
single pushbutton mode of operation and digital source
input control. Figure 2 provides a typical application
example of the dual pushbutton configuration for the
DS1669. In dual–pushbutton mode, the up–contact
input (UC) is used solely to provide upward movement
of the wiper position and the down–contact input (DC) is
used to provide downward movement of the wiper posi-
tion. For dual pushbutton configuration, all control
inputs (UC, DC, and D) must remain open on device
power–up.
The digital source input, D, was designed for micropro-
cessor or controller applications. This control input
manipulates the device in the same manner as the
single pushbutton configuration; controlling movement
of the wiper position in both upward and downward
directions. One added feature over the single pushbut-
ton configuration is the ability to increment or decrement
wiper position at a faster rate. Digital source input con-
trol is available regardless of the type of pushbutton
configuration.
OPERATION
The DS1668/DS1669 Dallastats are controlled through
a contact closure input or by a digital source input. The
DS1668 is configured to operate from a single contact
closure (pushbutton) input which is integrated in the
custom 6–pin package or the device can be driven from
the digital source input (D). The DS1669 can be con-
trolled using a single pushbutton input, dual pushbutton,
or using the digital source input.
022698 2/10
DS1668, DS1669, DS1669S
DS1669 SINGLE PUSHBUTTON CONFIGURATION (TYPICAL EXAMPLE)
Figure 1
DS1669
R
H
UC
D
R
L
V+
DC
R
W
V–
DS1669 DUAL PUSHBUTTON CONFIGURATION (TYPICAL APPLICATION)
Figure 2
DS1669
R
H
UC
D
R
L
V+
DC
R
W
V–
022698 3/10
DS1668, DS1669, DS1669S
Dallastats interpret input pulse widths as the means of
controlling wiper movement. A single pulse width input
over the UC, DC, or D terminals will cause the wiper
position to move 1/64th of the total resistance. All
inputs, UC, DC, or D, are inactive when in the high state.
A transition from a high to low on these inputs is consid-
ered the beginning of pulse activity.
A single pulse is defined as being greater than 1 ms but
lasting no longer than a second when using the contact
closure inputs UC and DC. When using the D input a
single pulse is defined as being greater than 1
µs
but
lasting no longer than 1 second. This is shown in Fig-
ures 4a and 6a. Repetitive pulsed inputs can be used to
step through each resistive position of the device (see
Figures 4a and 6b). The requirement for repetitive
pulsed inputs is that pulses must be separated by a
minimum time of 1 ms. If not, the Dallastat will interpret
repetitive pulses as a single continuous pulse.
Pulse inputs lasting longer than 1 second will cause the
wiper to move one position every 100 ms following the
initial 1 second hold time. The total time to transcend the
entire potentiometer using a continuous input pulse is
given in the equation below:
1 (second) + 63 X 100 ms = 7.3 (seconds)
In single pushbutton mode or when using the digital
source input, as the wiper reaches the end of the poten-
tiometer its direction of movement reverses. This will
occur whether or not the input is a continuous pulse or a
sequence of repetitive pulses. Changing the direction of
wiper movement in single pushbutton mode or digital
source mode is also accomplished by a period of inac-
tivity on the UC or D inputs for (minimum) 1 second or
greater. In dual pushbutton mode, the direction is con-
trolled by the UC and DC inputs. No wait states are
required to change wiper direction in dual pushbutton
mode. Additionally, in dual pushbutton mode as the
wiper reaches the end of the potentiometer, the direc-
tion of wiper movement will not change. Wiper position
will remain at the potentiometers’ end until an opposite
direction input is given.
All control inputs, UC, DC, and D, are internally pulled
up with a 100K ohm resistance. Additionally, the UC and
DC inputs are internally debounced and require no
external components for input signal conditioning.
The DS1668/DS1669 are provided with two supply
inputs –V and +V. The maximum voltage difference
between the two supply inputs is + 8.0 volts while the
minimum voltage difference is +4.5 volts. All input levels
are referenced to the negative supply input, –V. The volt-
age applied to any Dallastat terminal must not exceed the
negative supply voltage (–V ) by –0.5 or the positive sup-
ply voltage (+V) by + 0.5 volts. The minimum logic high
level must be +2.4 volts with reference to the –V supply
voltage input. A logic low level with reference to the –V
supply voltage has a maximum value of +0.8 volts. Dal-
lastats exhibit a typical wiper resistance of 400 ohms with
a maximum wiper resistance of 1000 ohms. The maxi-
mum wiper current allowed through the Dallastat is speci-
fied at 1 milliamps (see DC Electrical Characteristics).
NONVOLATILE WIPER SETTINGS
Dallastats maintain the position of the wiper in the
absence of power. This feature is provided through the
use of EEPROM type memory cell arrays. During nor-
mal operation the position of the wiper is determined by
the input multiplexer. Periodically, the multiplexer will
update the EEPROM memory cells. The manner in
which an update occurs has been optimized for reliabil-
ity, durability, and performance. Additionally, the update
operation is totally transparent to the user.
When power is applied to the Dallastat, the wiper setting
will be the last recorded in the EEPROM memory cells.
If the Dallastat setting is changed after power is applied,
the new value will be stored after a delay of 2 seconds.
The initial storage of a new value after power–up,
occurs when the first change is made, regardless of
when this change is made.
After the initial change on power–up, subsequent
changes in the Dallastat EEPROM memory cells will
occur only if the wiper position of the part is moved
greater than 12.5% of the total resistance range. Any
wiper movement after initial power–up which is less
than 12.5% will not be recorded in the EEPROM
memory cells. Since the Dallastat contains a 64–to–1
multiplexer, a change of greater than 12.5% corre-
sponds to a change of the fourth LSB.
Changes or storage to the EEPROM memory cells must
allow for a 2 second delay to guarantee that updates will
occur. The EEPROM memory cells are specified to
accept greater than 80,000 writes before a wear–out
condition. If the EEPROM memory cells do reach a
wear–out condition, the Dallastat will still function prop-
erly while power is applied. However, on power–up the
device’s wiper position will be that of the position last
recorded before memory cell wear out.
022698 4/10
DS1668, DS1669, DS1669S
DS1668 DALLASTAT
TM
BLOCK DIAGRAM
Figure 3
+
D
INPUT
INTERPRETER
AND CONTROL
UC
DC
-
R
L
SHADOW MEMORY
64 TO 1 MUXER
R
H
RHEOSTAT
NOTE:
R
W
DOTTED LINE CONNECTIONS AND
COMPONENTS ARE INTERNAL TO
THE DS1668 AND DO NOT EXIST ON
THE DS1669.
FLOWCHART: ONE BUTTON OPERATION AND ELECTRICAL CONTROL
Figure 4
CONTACT CLOSURE
(D OR UC)
INCREMENT/DECREMENT
1/64TH
NO
CONTACT CLOSED
CONTINUOUSLY
> 1 SEC ?
NO
LIMIT REACHED
OR
CONTACT OPEN
1 SEC ?
YES
REVERSE DIRECTION
YES
INCREMENT/DECREMENT
ON 100MS INTERVALS
CONTACT OPEN AND CONTACT CLOSURE TIMING IS 1s
±
10%
022698 5/10
京公网安备 11010802033920号
EEWORLD
