EEWORLDEEWORLDEEWORLD

Part Number

Search

5KP26A/51

Description
Trans Voltage Suppressor Diode, 5000W, 26V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, CASE P600, 2 PIN
CategoryDiscrete semiconductor    diode   
File Size108KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

5KP26A/51 Overview

Trans Voltage Suppressor Diode, 5000W, 26V V(RWM), Unidirectional, 1 Element, Silicon, PLASTIC, CASE P600, 2 PIN

5KP26A/51 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerVishay
package instructionO-PALF-W2
Contacts2
Manufacturer packaging codeCASE P600
Reach Compliance Codeunknown
ECCN codeEAR99
Maximum breakdown voltage31.9 V
Minimum breakdown voltage28.9 V
Shell connectionISOLATED
ConfigurationSINGLE
Diode component materialsSILICON
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
JESD-30 codeO-PALF-W2
JESD-609 codee0
Maximum non-repetitive peak reverse power dissipation5000 W
Number of components1
Number of terminals2
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formLONG FORM
Peak Reflow Temperature (Celsius)NOT SPECIFIED
polarityUNIDIRECTIONAL
Maximum power dissipation8 W
Certification statusNot Qualified
Maximum repetitive peak reverse voltage26 V
surface mountNO
technologyAVALANCHE
Terminal surfaceTIN LEAD
Terminal formWIRE
Terminal locationAXIAL
Maximum time at peak reflow temperatureNOT SPECIFIED
5KP5.0 thru 5KP188A
Vishay Semiconductors
formerly General Semiconductor
T
RANS
Z
ORB
®
Transient Voltage Suppressors
Stand-off Voltage
5.0 to 188 V
Peak Pulse Power
5000 W
Features
• Glass passivated junction
• 5000 W peak pulse power capability with a
10/1000
µs
waveform, repetition rate (duty cycle):
0.05 %
• Excellent clamping capability
• Low incremental surge resistance
• Very fast response time
• Devices with V
(BR)
> 10 V I
D
are typically less than
1.0
µA
• Available in uni-directional polarity only
• Meets MSL level 1 per J-STD-020C
• AEC-Q101 qualified
Mechanical Data
Case:
Molded plastic body over glass passivated
junction. Epoxy meets UL 94V-0 Flammability rating
Terminals:
Solder plated or matte tin plated
(E3 Suffix) leads, Solderable per J-STD-002B and
Mil-STD-750, Method 2026
High temperature soldering guaranteed:
265 °C/10 seconds, 0.375" (9.5 mm) lead length,
5 lbs. (2.3 kg) tension
Polarity:
The color band denotes the cathode, which
is positive with respect to the anode under normal
TVS operation
Maximum Ratings and Characteristics
Ratings 25 °C, unless otherwise specified
Parameter
Peak pulse power dissipation
Peak pulse current
Steady state power dissipation
Peak forward surge current
Instantaneous forward voltage
Operating junction and storage
temperature range
Notes:
(1) Non-repetitive current pulse, per Fig. 3 and derated above T
A
= 25 °C per Fig. 2.
(2) Mounted on copper pad area of 1.6 x 1.6" (40 x 40 mm) per Fig. 5.
(3) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum
Test condition
10/1000
µs
waveform
(1)
10/1000
µs
waveform
(1)
lead lengths 0.375“ (9.5 mm),
T
L
= 75 °C
100 A
(3)
(2)
Symbol
P
PPM
I
PPM
P
M(AV)
I
FSM
V
F
T
J
, T
STG
Value
5000
See next table
8.0
600
3.5
-55 to +175
Unit
W
A
W
A
V
°C
8.3 ms single half sine-wave
(3)
Document Number 88308
Rev. 1.2, 27-Oct-04
www.vishay.com
1
Recommended PIC chip [radio control function]
[align=left][color=black][font=SimSun][size=9.0pt]I want to ask a small question[/size][/font][/color][color=black][font="][size=9.0pt] [/size][/font][/color][color=black][font=SimSun][size=9.0pt]I ne...
huwiam99 Microchip MCU
EPCS chip programming problem
I want to ask, after programming the EPCS chip through the CONFIG port, if I do not unplug the download line, the FPGA will not start up when I power it on again, nSTATUS will be pulled low, and CONF_...
eeleader-mcu FPGA/CPLD
Questions about multisim simulation
I was recently simulating a 555 oscillator. The square wave I output was input to a voltage follower and then connected to an integrator to get a triangle wave. The problem is as shown in the figure b...
音速兔 Analog electronics
Help, STM32F103 ADC problem
I use two ADCs for data acquisition. No matter in independent mode or synchronous mode, PA0 (channel 0) will have burr-like signals, and PA1 (channel 1) will have a level of about 1.7V (half of the 3....
laowen_110 stm32/stm8
TLC adopts AC voltage
I want to use TLC2543 to collect the instantaneous value of AC. The frequency of AC signal is only 50HZ. I wonder if the speed can be increased in time?...
晴歌 Analogue and Mixed Signal
Design of audio products based on DSP
With the acceleration of the digitalization process, digital signals will replace more analog signal environments. Since 2004, the application of DSP in consumer electronics will enter people's lives ...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1754  583  1653  2435  745  36  12  34  50  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号