1200HGH200JF25B datasheet, PDF

1200HGH200JF25B: DescriptionStrain Guage Sensor, Gage, 0Psi Min, 2000Psi Max, 0.5%, 1-5V, Cylindrical; CategoryThe sensor Sensor/transducer; File Size507KB，4 Pages; ManufacturerGems Sensors & Controls

Download Datasheet Parametric View All

1200HGH200JF25B Overview

Strain Guage Sensor, Gage, 0Psi Min, 2000Psi Max, 0.5%, 1-5V, Cylindrical

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Reach Compliance Code	unknow
Maximum accuracy(%)	0.5%
shell	STAINLESS STEEL
Nominal offset	1V
Maximum operating temperature	50 °C
Minimum operating temperature	-20 °C
Output range	1-5V
Output type	ANALOG VOLTAGE
Package Shape/Form	CYLINDRICAL
port type	1/4 NPT MALE
Maximum pressure range	2000 Psi
Minimum pressure range
Pressure sensing mode	GAGE
Sensor/Transducer Type	PRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage	35 V
Minimum supply voltage	1.5 V
Termination type	CABLE
Base Number Matches	1

Check out the new post function, everyone take a look~~~: Previously, Blue Eye Fox and wangjiafu1985 suggested that the forum should have a function to view new posts. This function was added today:As shown in the figure: Label 1 remains the same, including ...; soso Suggestions & Announcements

Winding inductance of electrolytic capacitor: The electrolytic capacitor is made of two strips of aluminum foil with insulating paper. Because it is wound, it is considered to be an inductor. This conclusion has been circulated for decades. I don...; PowerAnts Analog electronics

As a beginner, how can I learn the relevant knowledge of WINCE?: Since I will be going to the company for internship in two months, the engineer from the relevant department of the company informed me that I should first familiarize myself with the wince system and...; t63056 Embedded System

How does COMBOBOX get focus?: I want to do something when COMBOBOX gets the focus. The method I used is if(GetFoucs()->GetDlgCtrlID==IDC_XXX), but the cursor is clearly on COMBOBOX but it doesn't seem to get the focus. The same co...; 2002xiao Embedded System

I have some questions about a small program and need some advice: module count4(out,reset,clk); output[3:0] out; input[3:0] reset,clk; reg[3:0] out; always @(posedge clk)beginif(reset) out=0;else out=out+1;end endmoduleIs the reason why out is defined as a register ...; leomeng FPGA/CPLD

2440, bootloader problem: My bsp contains stepldr and eboot, I want to run eboot, but after burning stepldr.nb1 into flash, dnw shows garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Init(void) ...; ricky03221115 Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components