Chip tantalum capacitors
TC Series A Case
Features
1) Small package, large capacitance chip tantalum capacitor.
2) Low impedance capacitors.
3) Screening by thermal shock.
Datasheet
Dimensions
Anode mark
(Unit : mm)
Dimensions
L
H
W
1
Size
L
W
1
W
2
3.2
±
0.2
1.6
±
0.2
1.2
±
0.2
1.6
±
0.2
0.8
±
0.3
W
2
H
S
S
+
S
−
Part
No. Explanation
T C
1
1
A
2
0
3
J
1
0
4
4
6
M
5
8 R
6
Series name
TC
Nominal capacitance
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
2
Case style
A : 3216-18 (1206) size
5
Capacitance tolerance
M :
±
20%
3
Rated voltage
4 6.3 10 16 20 25
0G 0J 1A 1C 1D 1E
6
Rated voltage (V)
CODE
Taping
8 : Real width : 8mm
R : Positive electrode on the side opposite to sprocket hole
www.rohm.com
c
○
2013 ROHM Co., Ltd. All rights reserved.
1/7
2013.03 - Rev.I
TC Series A Case
Rated
table
Rated voltage (V.DC)
4
6.3
10
16
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
20
A
25
A
Datasheet
Capacitance
(μF)
1.0 (105)
2.2 (225)
3.3 (335)
4.7 (475)
10 (106)
15 (156)
22 (226)
33 (336)
47 (476)
100 (107)
Remark) Case size codes (A) in the above show products line-up.
Marking
The indications listed below should be given on the surface of a capacitor.
: The polarity should be shown by bar. (on the anode side)
(1) Polarity
(2) Rated DC voltage : A voltage code is shown as below table.
(3) Capacitance
: A capacitance code is shown as below table.
Voltage
Code
g
j
A
C
D
E
Rated DC
Voltage (V)
4
6.3
10
16
20
25
Capacitance
Code
A
E
J
N
S
a
e
j
n
s
_
a
Nominal
Capacitance (μF)
1.0
1.5
2.2
3.3
4.7
10
15
22
33
47
100
Visual typical example
voltage code and capacitance code are variable with parts number.
[A case]
EX.)
j
−
(1)
a
−
(2)
(2) capacitance code
manufacture code
j a
(1) voltage code
www.rohm.com
c
○
2013 ROHM Co., Ltd. All rights reserved.
2/7
2013.11 - Rev.J
TC Series A Case
Characteristics
Item
Operating Temperature
Maximum operating
temperature with no voltage
derating
Rated voltage (V.DC)
Category voltage (V.DC)
Surge voltage (V.DC)
DC Leakage current
−55°C~+125°C
+85°C
4 6.3 10 16 20 25
2.5 4 6.3 10 13 16
5
8 13 20 26 32
Shall be satisfied the value on
" Standard list "
at 85°C
at 125°C
at 85°C
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 1min
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms
+1.5V.DC
Measuring circuit
: DC Equivalent series circuit
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms
+1.5V.DC
Measuring circuit
: DC Equivalent series circuit
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
Measuring frequency : 100±10kHz
Measuring voltage : 0.5Vrms or less
: DC Equivalent series circuit
Measuring circuit
Performance
Datasheet
Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds
+85°C
Capacitance tolerance
Shall be satisfied allowance range.
±20%
Tangent of loss angle
(Df, tan
δ)
Shall be satisfied the value on
" Standard list "
Impedance
Shall be satisfied the value on
" Standard list "
Resistance to
Soldering heat
Appearance
L.C.
C/C
Df (tan
δ)
There should be no significant abnormality.
The indications should be clear.
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Less than initial limit
Solder temp
: 260±10°C
: 5±0.5s
Duration
TCA0G107M8R : Within
±20%
of initial value
Repetition
:1
Others
: Within
±5%
of initial value
After the specimens, leave it at room temperature for
Less than initial limit
over 24h and then measure the sample.
There should be no significant abnormality.
The indications should be clear.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Temp.
1
2
3
4
−55±3°C
Room temp.
125±2°C
Room temp.
Time
30±3min.
3min.or less
30±3min.
3min.or less
Temperature
cycle
Appearance
L.C.
C/C
Less than initial limit
TCA0G107M8R : Within
±20%
of initial value
TCA0J476M8R : Within
±15%
of initial value
TCA1A226M8R : Within
±15%
of initial value
Others
: Within
±10%
of initial value
Df (tan
δ)
Moisture
resistance
Appearance
L.C.
C/C
Df (tan
δ)
Less than initial limit
There should be no significant abnormality.
The indications should be clear.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
Less than initial limit
condition that the temperature and humidity are
TCA0G107M8R : Within
±20%
of initial value 60±2°C and 90 to 95% RH,respectiveiy, for 500±12h
Others
: Within
±10%
of initial value leave it at room
temperature for over 24h and then measure the
TCA0G107M8R : Less than 150% of initial limit sample.
Others
: Less than initial limit
www.rohm.com
c
○
2013 ROHM Co., Ltd. All rights reserved.
3/7
2013.11 - Rev.J
TC Series A Case
Item
Temperature
Stability
Temp.
C/C
Df (tan
δ)
L.C.
Temp.
C/C
Df (tan
δ)
L.C.
Temp.
C/C
Df (tan
δ)
L.C.
Surge voltage
Appearance
L.C.
C/C
Df (tan
δ)
Appearance
Loading at
High temperature
L.C.
+85°C
TCA0G107M8R : Within
+12/0%
of initial value
Others
: Within
+10/0%
of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial limit
+125°C
Within
+15/0%
of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1250% of initial limit
−55°C
Within 0/−12% of initial value
Shall be satisfied the voltage on " Standard list "
−
Performance
Datasheet
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage via the serial resistance of
Less than initial limit
1kΩ every 5±0.5 min.
TCA0G107M8R : Within
±20%
of initial value for 30±5 s. each time in the atmospheric condition of 85±2°C.
Others
:
±10%
of initial value
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
Less than initial limit
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
TCA0G107M8R : Less than 125% of initial limit After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
TCA1A226M8R : Less than 125% of initial limit
at a temperature of 85±2°C, leave the sample at room
TCA1E105M8R : Less than 125% of initial limit temperature / humidity for over 24h and measure the value.
: Less than initial limit
Others
TCA0G107M8R : Within
±20%
of initial value
TCA0J476M8R : Within
±15%
of initial value
TCA1A226M8R : Within
±15%
of initial value
Others
: Within±10% of initial value
Others
: Less than initial limit
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
(Unit : mm)
50
20
F (Apply force)
There should be no significant abnormality.
The indications should be clear.
There should be no significant abnormality.
The indications should be clear.
C/C
Df (tan
δ)
Terminal
strength
Capacitance
Appearance
The measured value should be stable.
There should be no significant abnormality.
R230
1
thickness=1.6mm
45
45
www.rohm.com
c
○
2013 ROHM Co., Ltd. All rights reserved.
4/7
2013.11 - Rev.J
TC Series A Case
Item
Adhesiveness
Performance
The terminal should not come off.
Datasheet
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
product
ja
Apply force
a circuit board
Dimensions
Refer to "External dimensions"
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30±5s, at room
temperature.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm
/
s
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration
: 3±0.5s
Solder
: M705
Flux
: Rosin 25% IPA 75%
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
Resistance to solvents
The indication should be clear
Solderability
3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
Vibration
Capacitance
Measure value should not fluctuate during
the measurement.
There should be no significant abnormality.
Appearance
www.rohm.com
c
○
2013 ROHM Co., Ltd. All rights reserved.
5/7
2013.11 - Rev.J
京公网安备 11010802033920号
EEWORLD
