Chip tantalum capacitors
(Bottom surface electrode type : Large capacitance)
TCT Series AL Case
Datasheet
Features
1) Bottom electrode configuration results in significantly greater compactness.
2) Filet formation enables easy visibility after mounting.
3) Ideal for noise removal on power supply lines with limited space.
4) Eco-friendly halogen-free products.
Dimensions
Anode mark
(Unit : mm)
Dimensions
Size
L
H
L
W
1
3.2
±
0.2
1.6
±
0.2
1.2
±
0.2
1.1
±
0.1
0.8
±
0.2
W
1
W
2
H
S
W
2
W
1
S
+
S
−
Part
No. Explanation
T C T
1
1
A L
2
1 A
3
4
4
7
4
6
M
5
8 R
6
Series name
TCT
Nominal capacitance
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
2
Case style
AL : 3216-12 (1206) size
5
Capacitance tolerance
M :
±
20%
3
Rated voltage
6
Rated voltage (V) 2.5 4 6.3 10 16 20 25 35
CODE
0E 0G 0J 1A 1C 1D 1E 1V
Taping
8 : Tape width
R : Positive electrode on the side opposite to sprocket hole
∗This
specification has possibility of charge, due to underdevelopment product.
Please ask for latest specification to our sales.
www.rohm.com
c
○
2015 ROHM Co., Ltd. All rights reserved.
1/6
2015.05 - Rev.K
TCT Series AL Case
Rated
table
Datasheet
(ESR : mΩ)
Capacitance
(μF)
1.0 (105)
1.5 (155)
2.2 (225)
3.3 (335)
4.7 (475)
10 (106)
15 (156)
22 (226)
33 (336)
47 (476)
100 (107)
150 (157)
220 (227)
330 (337)
Rated voltage (V.DC)
2.5
4
6.3
10
16
20
25
35
AL
AL
AL
AL
AL
AL
AL
AL
AL
AL
AL
AL
Under development
AL
AL
AL
AL
AL
Remark) Case size codes (AL) in the above show products line-up.
Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage : A voltage code is shown as below table.
(3) Capacitance
: A capacitance code is shown as below table.
Voltage
Code
e
g
j
A
C
D
E
V
Visual typical example
voltage code and capacitance code are variable
with parts number.
[AL case]
Rated DC
Voltage (V)
2.5
4
6.3
10
16
20
25
35
Capacitance
Code
A
J
N
S
a
e
j
n
s
_
a
_
e
_
j
_
n
Nominal
Capacitance (μF)
1.0
2.2
3.3
4.7
10
15
22
33
47
100
150
220
330
EX.)
A
−
(1)
s
−
(2)
(2) capacitance code
(1) voltage code
As
manufacture code
www.rohm.com
c
○
2015 ROHM Co., Ltd. All rights reserved.
2/6
2015.05 - Rev.K
TCT Series AL Case
Characteristics
Item
Operating Temperature
Maximum operating
temperature with no voltage
derating
Rated voltage (V.DC)
Category voltage (V.DC)
Surge voltage (V.DC)
DC Leakage current
+85°C
2.5 4 6.3 10 16 20 25 35
1.6 2.5 4 6.3 10 13 16 22
3.2 5.0 8 13 20 26 32 44
Shall be satisfied the value on
" Standard list "
at 85°C
at 125°C
at 85°C
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 5min
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms
+1.5V.DC
: DC Equivalent series circuit
Measuring circuit
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms
+1.5V.DC
Measuring circuit
: DC Equivalent series circuit
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
Measuring frequency : 100±10kHz
Measuring voltage : 0.5Vrms or less
: DC Equivalent series circuit
Measuring circuit
Performance
−55°C
to
+125°C
Datasheet
Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds
+85°C
Capacitance tolerance
Shall be satisfied allowance range.
±20%
Tangent of loss angle
(Df, tan
δ)
Shall be satisfied the value on
" Standard list "
Impedance
Shall be satisfied the value on
" Standard list "
Resistance to
Soldering heat
Appearance
L.C.
C/C
There should be no significant abnormality.
The indications should be clear.
Less than initial limit
Within
+20/−30%
of initial value
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Solder temp
: 260±5°C
: 5±0.5s
Duration
Repetition
:1
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Df (tan
δ)
Less than 200% of initial limit
Temperature
cycle
Appearance
L.C.
C/C
There should be no significant abnormality.
The indications should be clear.
Less than 200% of initial limit
Within
±30%
of initial value
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Temp.
1
2
3
−55±3°C
Room temp.
125±2°C
Room temp.
Time
30±3min.
3min. or less
30±3min.
3min. or less
Df (tan
δ)
Less than 200% of initial limit
4
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Moisture
resistance
Appearance
L.C.
C/C
Df (tan
δ)
There should be no significant abnormality.
The indications should be clear.
Less than 200% of initial limit
Within
±20%
of initial value
Less than 300% of initial limit
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60±2°C and 90 to 95% RH, respectiveiy, for 500±12h
leave it at room
temperature for over 24h and then measure the
sample.
www.rohm.com
c
○
2015 ROHM Co., Ltd. All rights reserved.
3/6
2015.05 - Rev.K
TCT Series AL Case
Item
Temperature
Stability
Temp.
C/C
Df (tan
δ)
L.C.
Temp.
C/C
Df (tan
δ)
L.C.
Temp.
C/C
Df (tan
δ)
L.C.
Surge voltage
Appearance
L.C.
C/C
Df (tan
δ)
+85°C
Within
+15/0%
of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial limit
+125°C
Within
+20/0%
of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1250% of initial limit
There should be no significant abnormality.
Less than 200% of initial value
Within
±20%
of initial value
Less than 200% of initial limit
−55°C
Within 0/−15% of initial value
Shall be satisfied the voltage on " Standard list "
−
Performance
Datasheet
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
Loading at
Appearance
High temperature
L.C.
C/C
There should be no significant abnormality.
Less than 200% of initial limit
Within
+20/−30%
of initial value
Df (tan
δ)
Less than 300% of initial limit
Terminal
strength
Capacitance
Appearance
The measured value should be stable.
There should be no significant abnormality.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
(Unit : mm)
50
20
F (Apply force)
R230
1
thickness=1.6mm
45
45
Adhesiveness
The terminal should not come off.
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
product
ja
Apply force
a circuit board
www.rohm.com
c
○
2015 ROHM Co., Ltd. All rights reserved.
4/6
2015.05 - Rev.K
TCT Series AL Case
Item
Dimensions
Performance
Refer to "External dimensions"
Datasheet
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30±5s, at room
temperature.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm
/
s
Pre-treatment (accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration
: 3±0.5s
Solder
: M705
Flux
: Rosin 25% IPA 75%
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
Resistance to solvents
The indication should be clear
Solderability
3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
Vibration
Capacitance
Measure value should not fluctuate during
the measurement.
There should be no significant abnormality.
Appearance
Standard
products list
Df
Impedance
Leakage
120Hz
100kHz
current
(%)
25°C
1WV.5min
25°C
−55°C
85°C 125°C
(μA)
(Ω)
5.5
16.5
4
8.8
6.3
94.5
280
3.3
4.7
50
2.4
3.6
5.3
2
4.4
1.2
1.2
35
80
35
35
34
80
80
35
35
80
30
35
35
30
35
30
30
20
30
20
20
18
30
30
15
20
30
15
20
20
15
20
15
15
25
40
25
25
24
40
40
20
25
40
20
25
25
20
25
20
20
2.5
2.5
3
2.5
3
2.7
2.5
4
4
2.5
4
4
4
8
4
8
8
Part No.
Rated
voltage
85°C
(V)
Category
voltage
125°C
(V)
1.6
1.6
2.5
2.5
4
4
4
6.3
6.3
6.3
10
10
10
13
13
16
22
Surge
voltage
85°C
(V)
3.3
3.3
5.2
5.2
8
8
8
13
13
13
20
20
20
26
26
33
45
Cap.
120Hz
Tolerance
(μF)
220
330
100
220
100
150
220
33
47
100
15
22
33
10
22
4.7
3.3
(%)
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
±
20
TCT AL 0E 227 M8R
TCT AL 0E 337 M8R
TCT AL 0G 107 M8R
TCT AL 0G 227 M8R
TCT AL 0J 107 M8R
TCT AL 0J 157 M8R
∗
TCT AL 0J 227 M8R
TCT AL 1A 336 M8R
TCT AL 1A 476 M8R
∗
TCT AL 1A 107 M8R
TCT AL 1C 156 M8R
TCT AL 1C 226 M8R
TCT AL 1C 336 M8R
TCT AL 1D 106 M8R
TCT AL 1D 226 M8R
TCT AL 1E 475 M8R
TCT AL 1V 335 M8R
∗
= Under development
2.5
2.5
4
4
6.3
6.3
6.3
10
10
10
16
16
16
20
20
25
35
www.rohm.com
c
○
2015 ROHM Co., Ltd. All rights reserved.
5/6
2015.05 - Rev.K
京公网安备 11010802033920号
EEWORLD
