FAR-F5CM-836M50-B268-Y datasheet, PDF

Datasheet> All Categories > Analog mixed-signal IC> filter> FAR-F5CM-836M50-B268-Y

FAR-F5CM-836M50-B268-Y: DescriptionSAW Filter, 6 Pin(s), Plastic; CategoryAnalog mixed-signal IC filter; File Size120KB，15 Pages; ManufacturerFUJITSU; Websitehttp://edevice.fujitsu.com/fmd/en/index.html

Download Datasheet Parametric Compare View All

FAR-F5CM-836M50-B268-Y Overview

SAW Filter, 6 Pin(s), Plastic

FAR-F5CM-836M50-B268-Y Parametric

Parameter Name	Attribute value
Maker	FUJITSU
Reach Compliance Code	compliant
filter type	SAW FILTER
Installation type	SURFACE MOUNT
Number of terminals	6
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
Packaging Materials	PLASTIC

Preview

Download Datasheet

View All

FUJITSU MEDIA DEVICE

DATA SHEET

DS04-23119-5E

ASSP

Mobile Communication Systems

Piezoelectric SAW BPF

(700 MHz to 1000 MHz)

F5CM Series (B2)

DESCRIPTION

The F5CM series of SAW filters have balanced in/unbalanced out or unbalanced in/balanced out of I/O ports.

Therefore these filters are suitable for the design using balanced type of IC. By using these filters, any transforming

devises, such as balun is not required.

The F5CM series filters apply to the frequency range 700 MHz to 1000 MHz. High performance has been realized

with high reliability and small size by using original materials and original design.

The F5CM series filters are suitable for RF interstage filter in mobile communication systems and standard parts

are available for GSM and AMPS/TDMA/CDMA standards.

FEATURES

•

Balanced/unbalanced I/O ports

Ultra compact and light package (3.0 mm

3.0 mm package)

Any external matching circuit is not required

Excellent stop-band attenuation

Small pass-band ripple

Surface mount package (SMT)

PACKAGE

FAR-F5CM-836M50-B268-Y Related Products

	FAR-F5CM-836M50-B268-Y	FAR-F5CM-947M50-B260-X	FAR-F5CM-947M50-B260-Y	FAR-F5CM-942M50-B270-X	FAR-F5CM-881M50-B266-Y
Description	SAW Filter, 6 Pin(s), Plastic	SAW Filter, 6 Pin(s), Plastic	SAW Filter, 6 Pin(s), Plastic	SAW Filter, 6 Pin(s), Plastic	SAW Filter, 6 Pin(s), Plastic
Maker	FUJITSU	FUJITSU	FUJITSU	FUJITSU	FUJITSU
Reach Compliance Code	compliant	unknown	unknown	compliant	compliant
filter type	SAW FILTER	SAW FILTER	SAW FILTER	SAW FILTER	SAW FILTER
Installation type	SURFACE MOUNT	SURFACE MOUNT	SURFACE MOUNT	SURFACE MOUNT	SURFACE MOUNT
Number of terminals	6	6	6	6	6
Maximum operating temperature	85 °C	85 °C	85 °C	85 °C	85 °C
Minimum operating temperature	-30 °C	-30 °C	-30 °C	-30 °C	-30 °C
Packaging Materials	PLASTIC	PLASTIC	PLASTIC	PLASTIC	PLASTIC

Recommended Resources

Inductive feedback oscillator circuit

Audio remote control switch schematic diagram

temperature control

Double T-type frequency selective oscillator

Multipurpose charging circuit

Three-phase exhaust fan power-saving automatic control circuit

EEWORLD Website Terms of Service: [font=微软雅黑][size=3]Before registering, please read these Terms of Service carefully. If you register successfully, you will be deemed to have voluntarily accepted all the contents of these Terms of Se...; eric_wang Suggestions & Announcements

i2c basic settings problem: For those of you who have experience using i2c, there is currently a case where you need to use i2c to write and read the adc value. Test it before the component comes back. Currently, the loopback mo...; nt52241930 Microcontroller MCU

Wireless meter reading system for water, electricity and gas: 1. Composition of GPRS three-meter centralized meter reading and control system The master station reads, monitors and controls the metering data and related information of multiple wireless meters th...; shshangzhi RF/Wirelessly

The frequency of the maple output: I saw a post on the maple forum about converting the output frequency and tested it:) /* QuickererPin :-) * * Turns a GPIO pin on and off fast using direct updates. * Copyright 2010 G Bulmer */ // #in...; xmdesign stm32/stm8

Frequency division procedures: I wrote a program to divide the FPGA 50MHZ into 1HZ, but it seems not right. Can you help me find what is wrong? reg[22:0] counter; reg[1:0] clkout; always @(posedge clk) begin if(counter==25_000_000)...; hjl240 FPGA/CPLD

The difference between Cortex-A8 and ARM11: What are the differences between Cortex-A8 and ARM11 as two classic cores of ARM? Let's take a brief look at them:　　Cortex-A8 is a microprocessor based on ARMv7 instruction architecture, running at sp...; flyday ARM Technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components