The AS7C1024 and AS7C31024 are high performance CMOS 1,048,576-bit Static Random Access Memory (SRAM)
devices organized as 131,072 words × 8 bits. It is designed for memory applications where fast data access, low power, and
simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5/6/8/10 ns
are ideal for high performance applications. Active high and low chip enables (CE1, CE2) permit easy memory expansion
with multiple-bank systems.
When CE1 is high or CE2 is low the devices enter standby mode. If inputs are still toggling, the device will consume I
SB
power. If the bus is static, then full standby power is reached (I
SB1
or I
SB2
). For example, the AS7C31024 is guaranteed not
to exceed 0.33mW under nominal full standby conditions. All devices in this family will retain data when VCC is reduced as
low as 2.0V.
A write cycle is accomplished by asserting write enable (WE) and both chip enables (CE1, CE2). Data on the input pins I/
O0-I/O7 is written on the rising edge of WE (write cycle 1) or the active-to-inactive edge of CE1 or CE2 (write cycle 2). To
avoid bus contention, external devices should drive I/O pins only after outputs have been disabled with output enable (OE)
or write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and both chip enables (CE1, CE2), with write enable (WE)
high. The chips drive I/O pins with the data word referenced by the input address. When either chip enable is inactive, output
enable is inactive, or write enable is active, output drivers stay in high-impedance mode.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with V
CC
applied
DC current into outputs (low)
AS7C1024
AS7C31024
Symbol
V
t1
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
-0.50
–0.50
–
–65
–55
–
Max
+7.0
+5.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and func-
tional operation of the device at these or any other conditions outside those indicated in the operational sections of this spec ification is not implied. Expo-
sure to absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE1
H
X
L
L
L
CE2
X
L
H
H
H
WE
X
X
H
H
L
OE
X
X
H
L
X
Data
High Z
High Z
High Z
D
OUT
D
IN
Mode
Standby (I
SB
, I
SB1
)
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
Write (
ICC
)
Key: X = Don’t Care, L = Low, H = High
2
ALLIANCE SEMICONDUCTOR
10/18/00
®
AS7C1024
AS7C31024
Recommended operating conditions
Parameter
Supply voltage
Device
AS7C1024
AS7C31024
AS7C1024
Input voltage
AS7C31024
commercial
industrial
Symbol
V
CC
V
CC
V
IH
V
IH
V
IL†
Ambient operating temperature
†
Min
4.5
3.0
2.2
2.0
–0.5
0
–40
Nominal
5.0
3.3
–
–
–
–
–
Max
5.5
3.6
V
CC
+ 0.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
V
V
°C
°C
T
A
T
A
V
IL
min = –3.0V for pulse width less than t
RC/2
.
DC operating characteristics (over the operating range)
I always get stuck at the compile stage when using loops! No errors! Can I use loops without loops? Please give me a calculation! If I want to use loops, I can also program it! I only want the algorit...
[b]Table of Contents[/b] Chapter 1 The Development of Semiconductor Devices 1.1 “Tides and Waves” in the Development of Electronic Devices 1.2 Development from the Bulk Single Crystal Era to the Multi...
Dear experts, this is a program I wrote to measure the water level using ultrasonic waves. I modified it based on someone else's program. Now it doesn't respond. Nothing is displayed. I use a two-digi...
[i=s]This post was last edited by gh131413 on 2014-9-15 16:52[/i] This disease is called corpse water. It develops rapidly within 24 hours and the whole body is rotten. It seems that everyone should p...
As shown in the figure, we want to realize the LED flashing function [code] void delay (uint16_t delaytime) { uint16_t s = 0; while (s
The code is OK, the P0.1 breathing light is working, but the P0.0...
Embedded System
京公网安备 11010802033920号
EEWORLD
