CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Upgrade!
Surface Mount
NPCAP
●
Super
TM
-
low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
●
Rated voltage range : 2 to 10V
dc
, Capacitance range : 120 to 1,000µF
●
Case size range :φ5×4.5L toφ8×7.7L
●
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
●
RoHS Compliant
●
Halogen Free
PXF
Series
PXF
Lower ESR
PXE
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tan
δ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105℃
2 to 10V
dc
±20%
(M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.15
Characteristics
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Bias Humidity
Surge Voltage
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
(E46 : 1,000 hours ) at 105℃.
Appearance
No significant damage
Capacitance change
≦
±20%
of the initial value
DF (tan )
δ
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours (E46 : 500 hours ) .
Appearance
No significant damage
Capacitance change
≦
±20%
of the initial value
≦150%
of the initial specified value
DF (tan )
δ
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦
±20%
of the initial value
DF (tan )
δ
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105
℃
.
◆DIMENSIONS
[mm]
●
Terminal
◆MARKING
EX) 2.5V390µF
Code : A
W
Size Code
E46
E61
F61
F80
H70
H80
0.3max.
L
±
(Note)
0.3
A
±
0.2
φ
D
5
5
6.3
6.3
8
8
L
4.5
5.8
5.8
7.7
6.7
7.7
A
5.3
5.3
6.6
6.6
8.3
8.3
B
5.3
5.3
6.6
6.6
8.3
8.3
C
5.9
5.9
7.2
7.2
9.0
9.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.4
1.4
1.9
1.9
3.1
3.1
φD±
0.5
Note : L+0.1/-0.2 for E46
◆PART
NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PXF
A RA
M
0.2
C
±
F
69A
390
2.5
V
B
±
0.2
P
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 330µF:331, 1,000µF:102)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M
stm32/stm8
京公网安备 11010802033920号
EEWORLD
