K4S560832D
CMOS SDRAM
256Mbit SDRAM
8M x 8bit x 4 Banks
Synchronous DRAM
LVTTL
Revision 0.0
May. 2002
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 0.0 May. 2002
K4S560832D
Revision History
Revision 0.0 (May. , 2002)
CMOS SDRAM
Rev. 0.0 May. 2002
K4S560832D
8M x 8Bit x 4 Banks Synchronous DRAM
FEATURES
• JEDEC standard 3.3V power supply
• LVTTL compatible with multiplexed address
• Four banks operation
• MRS cycle with address key programs
-. CAS latency (2 & 3)
-. Burst length (1, 2, 4, 8 & Full page)
-. Burst type (Sequential & Interleave)
• All inputs are sampled at the positive going edge of the system
clock.
• Burst read single-bit write operation
• DQM for masking
• Auto & self refresh
• 64ms refresh period (8K Cycle)
Part No.
K4S560832D-NC/L7C
K4S560832D-NC/L75
K4S560832D-NC/L1H
K4S560832D-NC/L1L
CMOS SDRAM
GENERAL DESCRIPTION
The K4S560832D is 268,435,456 bits synchronous high data rate
Dynamic RAM organized as 4 x 8,392,608 words by 8bits, fabri-
cated with SAMSUNG's high performance CMOS technology. Syn-
chronous design allows precise cycle control with the use of
system clock I/O transactions are possible on every clock cycle.
Range of operating frequencies, programmable burst length and
programmable latencies allow the same device to be useful for a
variety of high bandwidth, high performance memory system appli-
cations.
ORDERING INFORMATION
Max Freq.
133MHz(CL=2)
133MHz(CL=3)
100MHz(CL=2)
100MHz(CL=3)
LVTTL
54pin
sTSOP(II)
Interface Package
FUNCTIONAL BLOCK DIAGRAM
I/O Control
LWE
Data Input Register
LDQM
Bank Select
8M x 8
8M x 8
8M x 8
8M x 8
Refresh Counter
Output Buffer
Row Decoder
Sense AMP
Row Buffer
DQi
Address Register
CLK
ADD
Column Decoder
Col. Buffer
Latency & Burst Length
LRAS
LCBR
LCKE
LRAS
LCBR
LWE
LCAS
Programming Register
LWCBR
LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
L(U)DQM
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 0.0 May. 2002
K4S560832D
PIN CONFIGURATION
(Top view)
VDD
DQ0
VDDQ
NC
DQ1
VSSQ
NC
DQ2
VDDQ
NC
DQ3
VSSQ
NC
VDD
NC
WE
CAS
RAS
CS
BA0
BA1
AP/A10
A0
A1
A2
A3
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
VSS
DQ7
VSSQ
NC
DQ6
VDDQ
NC
DQ5
VSSQ
NC
DQ4
VDDQ
NC
VSS
NC
DQM
CLK
CKE
A12
A11
A9
A8
A7
A6
A5
A4
VSS
CMOS SDRAM
54 PIN sTSOP(II)
300mil x 551mil
(7.62mm x 14.00mm)
(0.5 mm PIN PITCH)
Bank Address
BA0-BA1
Row Address
A0-A12
Auto Precharge
A10
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
PIN FUNCTION DESCRIPTION
Pin
CLK
CS
Name
System clock
Chip select
Input Function
Active on the positive going edge to sample all inputs.
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
Row/column addresses are multiplexed on the same pins.
Row address : RA
0
~ RA
12
, Column address : CA
0
~ CA
9
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
Enables write operation and row precharge.
Latches data in starting from CAS, WE active.
Makes data output Hi-Z, t
SHZ
after the clock and masks the output.
Blocks data input when DQM active.
Data inputs/outputs are multiplexed on the same pins.
Power and ground for the input buffers and the core logic.
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
This pin is recommended to be left No Connection on the device.
CKE
Clock enable
A
0
~ A
12
BA
0
~ BA
1
RAS
CAS
WE
DQM
DQ
0
~
7
V
DD
/V
SS
V
DDQ
/V
SSQ
N.C/RFU
Address
Bank select address
Row address strobe
Column address strobe
Write enable
Data input/output mask
Data input/output
Power supply/ground
Data output power/ground
No connection
/reserved for future use
Rev. 0.0 May. 2002
K4S560832D
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on any pin relative to Vss
Voltage on V
DD
supply relative to Vss
Storage temperature
Power dissipation
Short circuit current
Symbol
V
IN
, V
OUT
V
DD
, V
DDQ
T
STG
P
D
I
OS
Value
-1.0 ~ 4.6
-1.0 ~ 4.6
-55 ~ +150
1
50
CMOS SDRAM
Unit
V
V
°C
W
mA
Note :
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to V
SS
= 0V, T
A
= 0 to 70°C)
Parameter
Supply voltage
Input logic high voltage
Input logic low voltage
Output logic high voltage
Output logic low voltage
Input leakage current
Symbol
V
DD
, V
DDQ
V
IH
V
IL
V
OH
V
OL
I
LI
Min
3.0
2.0
-0.3
2.4
-
-10
Typ
3.3
3.0
0
-
-
-
Max
3.6
V
DD
+0.3
0.8
-
0.4
10
Unit
V
V
V
V
V
uA
1
2
I
OH
= -2mA
I
OL
= 2mA
3
Note
Notes :
1. V
IH
(max) = 5.6V AC. The overshoot voltage duration is
≤
3ns.
2. V
IL
(min) = -2.0V AC. The undershoot voltage duration is
≤
3ns.
3. Any input 0V
≤
V
IN
≤
V
DDQ
.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
CAPACITANCE
Clock
(V
DD
= 3.3V, T
A
= 23°C, f = 1MHz, V
REF
=1.4V
±
200 mV)
Pin
Symbol
C
CLK
C
IN
C
ADD
C
OUT
Min
2.5
2.5
2.5
4.0
Max
4.0
5.0
5.0
6.5
Unit
pF
pF
pF
pF
Note
1
2
2
3
RAS, CAS, WE, CS, CKE, DQM
Address
DQ
0
~ DQ
15
Notes :
1. -75/7C only specify a maximum value of 3.5pF
2. -75/7C only specify a maximum value of 3.8pF
3. -75/7C only specify a maximum value of 6.0pF
Rev. 0.0 May. 2002
Embedded System
京公网安备 11010802033920号
EEWORLD
