EEWORLDEEWORLDEEWORLD

Part Number

Search

S701031S2WCNQE

Description
SLIDE SWITCH, SPST, LATCHED, PANEL MOUNT, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size304KB,5 Pages
ManufacturerC&K
Environmental Compliance  
Download Datasheet Parametric View All

S701031S2WCNQE Overview

SLIDE SWITCH, SPST, LATCHED, PANEL MOUNT, ROHS COMPLIANT

S701031S2WCNQE Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerC&K
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeHIGH TYPE
body width17.27 mm
body height9.02 mm
Body length or diameter31.5 mm
Contact (AC) maximum rated R load15A@125VAC
Maximum contact current (AC)15 A
Maximum contact voltage (AC)125 V
Electrical life10000 Cycle(s)
JESD-609 codee4
Manufacturer's serial numberS
Installation featuresPANEL MOUNT
Maximum operating temperature65 °C
Minimum operating temperature-30 °C
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED
switch functionSPST
Switch typeSLIDE SWITCH
Terminal surfaceSilver (Ag)
Termination typeWIRE
S Series
Slide Switches
Features/Benefits
6 to 15 AMPS
Enclosed housing
PC and Snap-in panel mounting
Reversing option
RoHS compliant
Typical Applications
Portable tools
Small appliances
Floor care products
Models Available
Specifications
Materials
HOUSING: 6/6 nylon (UL94V-2), black.
TOP PLATE: 6/6 nylon (UL94V-2), black.
ACTUATOR: 6/6 nylon (UL94V-2), black (standard).
CONTACTS: Q contact material: Copper, silver plated. See page
I-31 for additional contact materials.
TERMINALS: Q contact material: Copper, silver plated. See page
I-31 for additional contact materials.
CONTACT SPRING: Music wire or stainless steel.
TERMINAL SEAL: Epoxy.
NOTE:
Any models supplied with Q, B or G contact material are RoHS compliant.
NOTE:
Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
I
Slide
CONTACT RATING: Q contact material (S1XX, S2XX Models):
6 AMPS @ 125 V AC; 6 AMPS @ 250 V AC; 1 AMP @
125 V DC (UL/CSA). (S5XX, S6XX Models): 12 AMPS @
125 V AC; 6 AMPS @ 250 V AC; 1 AMP @ 125 V DC (UL/CSA).
(S7XX, S8XX Models): 15 AMPS @ 125 V AC; 6AMPS @
250 V AC (UL/CSA). See page J-31 for additional ratings.
ELECTRICAL LIFE: 10,000 make-and-break cycles at full load.
CONTACT RESISTANCE: Below 10 m
typ. initial
@ 2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 109
min.
DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.
OPERATING TEMPERATURE: -30ºC to +65ºC
STORAGE TEMPERATURE: -30ºC to +85ºC
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages I–29 through I–32. For additional options not shown in catalog, consult Customer Service Center.
Switch Function
S101
SPST, 6 AMPS
S202
(DPDT, 6 AMPS
S802
DPDT, 15 AMPS
S102
SPDT, 6AMPS
S112
SPDT, mom., 6 AMPS
S201
DPST, 6 AMPS
S602
DPDT, 12 AMPS
S701
SPST, 15 AMPS
S702
SPDT, 15 AMPS
Actuator
03
.335" high
04
.500" high
09
.250" high
12
Screwdriver slot
(with marking)
13
Screwdriver slot
(without marking)
C2
Black cap
C3
Red cap
C5
Yellow cap
Detent
1
With detent
2
Without detent
Mounting Style
SS
Panel with mounting ears
MS
PC thru-hole
S2
Snap-in panel with blacktop plate
TS
Panel with mounting ears
Terminations
03
Solder lug with hole
02
PC Thru-hole
04
PC Thru-hole
07
Quick connect
08
PC Thru-hole
WC
Wire lead
Housing Markings
NONE
No markings
D
ON-OFF
L
ON
M
ON-OFF
N
Red rectangle on one end
Contact Material
Q
Silver
B
Gold
G
Gold over silver
Seal
NONE
No seal
E
Epoxy seal
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
I–28
www.ck-components.com
EEWORLD University Hall----Introduction to Isolation Amplifier
Introduction to Isolation Amplifier : https://training.eeworld.com.cn/course/5019...
wanglan123 Analog electronics
How to set the front side to run horizontally and the back side to run vertically
How to draw a PCB in Altium Designer, and make the front of the double-sided board run horizontally and the back run vertically by using a large number of vias, instead of the default routing during a...
巫毒猫 PCB Design
Switching Power Supply
How to design a constant current source controlled by a microcontroller for current sharing in parallel switching power supplies in buck circuits [[i] This post was last edited by Mumian on 2012-8-25 ...
木棉 Power technology
Recruitment for part-time STM32 project
Responsible for STM32 AD data collection and then transfer to PC via USB. 2009-06-16 -------------------------------------------------------------------------------- Guangzhou Ripu Electronics Co., Lt...
renfeide112 stm32/stm8
What should you do on the first anniversary of the Olympics?
Masan is about to reach the first anniversary of the Olympic Games. What should we do? ? ? I choose badminton. I don’t know what you guys are going to do. Share your thoughts!!! ^_^...
gaoxiao Talking
How to nest timers?
I want to write a program to control a running light with a periodic timer. Timer 0 controls the left shift at a slower rate. Timer 1 controls the right shift at a faster rate. I wrote this program ma...
suo618 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2764  1751  271  1988  2603  56  36  6  41  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号