EEWORLDEEWORLDEEWORLD

Part Number

Search

88572-1132J

Description
Board Connector, 132 Contact(s), 3 Row(s), Male, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size656KB,5 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

88572-1132J Overview

Board Connector, 132 Contact(s), 3 Row(s), Male, Straight, Solder Terminal

88572-1132J Parametric

Parameter NameAttribute value
MakerAmphenol
Reach Compliance Codecompliant
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL
Contact completed and terminatedGOLD (30) OVER NICKEL
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number88572
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded3
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts132
PDM: Rev:A
STATUS:
Released
Printed: May 14, 2011
.
Relay contact protection circuit
...
MrKingMCU Analog electronics
Power failure recovery through power consumption calculation utility
CTPL is a software utility for ultra-low-power MSP430FRxx FRAM microcontrollers that allows an application to save the CPU and peripheral states to non-volatile FRAM before the system is powered down ...
Jacktang Microcontroller MCU
Reprint: Some tips for searching electronic books
[p=25, null, left][color=rgb(0, 0, 0)][backcolor=rgb(249, 249, 249)][font=arial, helvetica, clean, sans-serif][size=2]I usually receive many inquiries about whether I can provide a certain e-book for ...
tiankai001 Download Centre
st7RC clock is inaccurate after adding PLL!
I use an ST7 RC oscillator and an auto-reload timer. When the PLL is disabled, the frequency is very accurate and is set to 4ms. When the multiplier 8 PLL is enabled at 5V, the clock is much worse and...
zhangq stm32/stm8
Issues to consider when designing multi-stage, high-gain circuits
When designing a multi-stage high-gain circuit, its stability index, noise index, bandwidth index, etc. are all different from those of a single stage. For multi-stage amplifiers, especially high gain...
dontium Analogue and Mixed Signal
Let's discuss what is the main reason that affects the system running speed under ce~~
The smaller one uses a 200M ep9315, and the one next door uses a 2440. I compared the two by trying the application program, and the interface switching speed is really too different. Just operating t...
andyye1630 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1731  870  726  467  2747  35  18  15  10  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号