EEWORLDEEWORLDEEWORLD

Part Number

Search

X4045P-2.7A

Description
1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
Categoryaccessories   
File Size889KB,24 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet View All

X4045P-2.7A Overview

1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8

DATASHEET
X4043, X4045
4k, 512 x 8 Bit CPU Supervisor with 4kbit EEPROM
FEATURES
• Selectable watchdog timer
• Low V
CC
detection and reset assertion
—Five standard reset threshold voltages
—Adjust low V
CC
reset threshold voltage using
special programming sequence
—Reset signal valid to V
CC
= 1V
• Low power CMOS
—<20µA max standby current, watchdog on
—<1µA standby current, watchdog OFF
—3mA active current
• 4kbits of EEPROM
—16-byte page write mode
—Self-timed write cycle
—5ms write cycle time (typical)
• Built-in inadvertent write protection
—Power-up/power-down protection circuitry
—Protect 0, 1/4, 1/2, all or 16, 32, 64 or 128 bytes
of EEPROM array with Block Lock
protection
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
• Available packages
—8 Ld SOIC
—8 Ld MSOP
—8 Ld PDIP
• Pb-free plus anneal available (RoHS compliant)
DESCRIPTION
The X4043/45 combines four popular functions,
Power-on Reset Control, Watchdog Timer, Supply
Voltage Supervision, and Block Lock Protect Serial
EEPROM Memory in one package. This combination
lowers system cost, reduces board space require-
ments, and increases reliability.
Applying power to the device activates the power-on
reset circuit which holds RESET/RESET active for a
period of time. This allows the power supply and oscilla-
tor to stabilize before the processor can execute code.
The Watchdog Timer provides an independent protec-
tion mechanism for microcontrollers. When the micro-
controller fails to restart a timer within a selectable
time out interval, the device activates the
RESET/RESET signal. The user selects the interval
from three preset values. Once selected, the interval
does not change, even after cycling the power.
The device’s low V
CC
detection circuitry protects the
user’s system from low voltage conditions, resetting the
system when V
CC
falls below the minimum V
CC
trip
point. RESET/RESET is asserted until V
CC
returns to
proper operating level and stabilizes. Five industry stan-
dard V
TRIP
thresholds are available, however, Intersil’s
unique circuits allow the threshold to be reprogrammed
to meet custom requirements or to fine-tune the thresh-
old for applications requiring higher precision.
FN8118
Rev 3.00
December 9, 2015
BLOCK DIAGRAM
Watchdog Transition
Detector
WP
SDA
Data
Register
Block Lock Control
Command
Decode &
Control
Logic
V
CC
Threshold
Reset logic
V
CC
V
TRIP
Protect Logic
Status
Register
EEPROM Array
2Kbits 1Kb 1Kb
RESET (X4043)
RESET (X4045)
Reset &
Watchdog
Timebase
Watchdog
Timer Reset
SCL
+
-
Power-on and
Low Voltage
Reset
Generation
FN8118 Rev 3.00
December 9, 2015
Page 1 of 24
Xiaomi Mi Band 2 and Mouse exchanged with E coins
I have been in poor health recently. I had severe stomach pain in the middle of the night. I went to the hospital several times. They said I had high cholesterol, gastroenteritis, fatty liver and a se...
pleasemissme Talking
Analog Circuit
How to make the voltage at a certain point in the circuit rise slowly to a certain value...
liuhe Analog electronics
Helical Microstrip Patch Antenna
Central topics: Brief Introduction of Mobile Terrestrial Digital Television SystemAntenna Design for Mobile Reception of Terrestrial Digital Television Solution: Determination of Microstrip Line Width...
随心 RF/Wirelessly
Ask a stupid question
In the analysis of the amplification factor of the deep feedback amplifier circuit, when the negative feedback circuit is connected in parallel Why does Us almost all fall on the resistor Rs?...
bin123186 Analog electronics
Android development program------I personally experiment with the code
It has been nearly ten days since I built the ANDROID platform. I have been following an unknown master, haha.I provide all the application test code I wrote myself... Comrades who need it can run... ...
shilaike Linux and Android
Common usage of MSP430 watchdog and writing method of interrupt function
The watchdog is set to prevent the program from running away, but since the watchdog is similar to a timer, it can be used as a timer. Example Code: Blink an LED with the Watchdog Timer #include msp43...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2008  1684  2544  2236  514  41  34  52  46  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号