EEWORLDEEWORLDEEWORLD

Part Number

Search

89232-406H

Description
Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size542KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

89232-406H Overview

Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

89232-406H Parametric

Parameter NameAttribute value
MakerAmphenol
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.095 inch
subject depth0.1 inch
body length0.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1500VAC V
maximum insertion force.556 N
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYCYCLOHEXYLENE TEREPHTHALLATE
Manufacturer's serial number89232
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature130 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts6
Power engineers are most afraid of EMC, analyze it like this! (Reposted)
[size=4] As the speed of switching power supplies is getting faster and faster, the power is getting higher and higher, and the density is getting larger and larger, interference problems will inevita...
qwqwqw2088 Analogue and Mixed Signal
Fingerprint matching algorithm help
There is a fingerprint matching algorithm, but I don’t know what the principle is. Have you seen such an algorithm? Fingerprint matching algorithm: - 1. Extract feature points from two images separate...
csfcsf Embedded System
Why is the stm32 pin reading different from the oscilloscope measurement?
The same pin, STM32 is set to input mode. The oscilloscope shows a high level, but the microcontroller pin reads a low level. Has anyone encountered the same phenomenon? What is the reason?...
shijizai stm32/stm8
TI Audio Module TPA3128D2 Evaluation Kit Evaluation 02 - Hardware Description
[i=s] This post was last edited by mzb2012 on 2017-10-26 21:06 [/i] [size=5][b] 1. Introduction [/b][/size] [size=5][b][size=5][b][size=5][/size][/b][/size][/b][size=4] The TPA3128D2 chip is a highly ...
mzb2012 TI Technology Forum
MSK modulation communication between CC1200 and CC430
Help: I configured CC430 to 250Kbps, MSK modulation. I want to communicate with CC1200. According to the datasheet, I set the rate to 250kbps, the debugging mode to 2-FSK, and the debugging frequency ...
huamao1987 RF/Wirelessly
sopc system clock
How is the system clock in sopc determined? The external crystal is 50mhz and is directly connected to the cpu without frequency division. Then I want to write a delay program in the ide, but I am not...
wall_e FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1807  123  505  237  1186  37  3  11  5  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号