DEVICE PARAMETERS, FIXED and ADJUSTABLE REGULATORS
f
O
Oscillator Frequency
50
52
100/
500
nA
kHz
kHz(min)
kHz(max)
V
V(max)
%
%(max)
A
A(min)
A(max)
mA(max)
mA
mA(max)
mA
mA(max)
µA
µA(max)
°C/W
47/
42
58/
63
Saturation Voltage
Max Duty Cycle (ON)
Current Limit
I
OUT
= 1A (
Note 4
)
(
Note 5
)
Peak Current, t
ON
≤
3µs (
Note 4
)
0.9
1.2/
1.4
98
93
2.2
1.7/
1.3
3.0/
3.2
2
75
30
5
10
Standby Quiescent Current
ON/OFF Pin = 5V (OFF)
50
200
65
45
2
85
100
1.4
1.2
4
30
ON /OFF Pin = 0V (ON)
0.01
10
2.2/
2.4
1.0/
0.8
V
SAT
DC
I
CL
I
L
Output Leakage Current
V
IN
= 40V, (
Note 6
),
(
Note 6
)
(
Note 6
)
Output = 0V
Output = –1V
Output = –1V
I
Q
I
STBY
Quiescent Current
T Package, Junction to Ambient (
Note 7
)
θ
JA
Thermal Resistance
T Package, Junction to Ambient (
Note 8
)
θ
JA
θ
JC
T Package, Junction to Case
N Package, Junction to Ambient (
Note 9
)
θ
JA
WM Package, Junction to Ambient (
Note 9
)
θ
JA
ON/OFF CONTROL, FIXED and ADJUSTABLE REGULATORS
Test Circuit Figure 1
V
IH
V
IL
I
IH
I
IL
Notes:
ON/OFF Pin Logic
Input Level
ON/OFF Pin Logic
Current
V
OUT
= 0V
V
OUT
= 5V
ON /OFF Pin = 5V (OFF)
V(min)
V(max)
µA
µA(max)
µA
µA(max)
1. Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical
Characteristics.
2. All limits guaranteed at room temperature (standard type face) and at
temperature extremes (bold type face).
All room temperature limits are100%
production tested. All limits at
temperature extreme
are guaranteed via testing.
3. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the
LM2575/LM1575 is used as shown in Figure 1 test circuit, system performance will be shown in system parameters section of Electrical
Characteristics.
4. Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output.
5. Feedback (pin 4) removed from output and connected to 0V.
6. Feedback (pin 4) removed from output and connected to 12V to force the output transistor OFF.
7. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/2" leads in a socket, or on PC
board with minimum copper area.
8. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/4" leads soldered to PC
board containing approximately 4 square inches of copper area surrounding the leads.
9. Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper will lower
This is a circuit that uses an operational amplifier to measure the β value of a transistor. It was designed and completed by myself. [img]http://s11.photo.store.qq.com/http_imgload.cgi?/rurl4_b=3374d...
I have recently encountered such a problem in the LPC2138 project. I would like to ask experts for advice: Because there is an LCD display without fonts in the project, and the required Chinese charac...
Recently I saw the development kit on Arrow: [url]https://www.eeworld.com.cn/mcu/2014/0829/article_16112.html[/url] So I placed an order, but they asked me to provide a 10-digit customs reg number. Ho...
Experimental purposeReview and consolidate the generation and operation of discrete signals in digital signal processing.Learn and master the method of generating discrete signals with MATLAB.Learn an...
Although I studied electronics, my seniors all laughed and said that after graduation, I still couldn't repair the phone (landline, not mobile phone), and I really didn't dare to admit that I graduate...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
