Exceeding the absolute maximum rating may damage the device.
The device is not guaranteed to function outside its operating rating.
Outputs loaded with 50Ω to ground.
Parameter
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
Condition
Min
2.0
Typ
Max
0.8
Units
V
V
µA
µA
+20
–250
–600
December 2009
4
M9999-121409-D
hbwhelp@micrel.com
or (408) 955-1690
Micrel, Inc.
SY89809L
AC Electrical Characteristics
(4)
T
A
= 0°C to +85°C, unless noted.
Symbol
t
PD
f
MAX
t
SKEW
t
SKPP
t
JITTER
V
PP
V
CMR
t
S
t
H
t
r
, t
f
Notes:
4.
5.
6.
7.
8.
9.
Outputs loaded with 50Ω to ground. Airflow
≥
300lfpm.
Differential propagation delay is defined as the delay from the crossing point of the differential input signals to the crossing point of the differential
output signals.
Output swing greater than 450mV.
The within-device skew is defined as the worst-case difference between any two similar delay paths within a single device operating at the same
voltage and temperature.
The part-to-part skew is defined as the absolute worst-case difference between any two delay paths on any two devices operating at the same
voltage and temperature.
The V
PP
(min) is defined as the minimum input differential voltage which will cause no increase in the propagation delay.
Parameter
Propagation Delay
(5)
Maximum Operating Frequency
(6)
Within-Device Skew
(7)
Part-to-Part Skew
(8)
Phase Noise(RMS)
Minimum Input Swing
LVPECL_CLK
(9)
Condition
Min
825
500
Typ
1050
Max
1275
50
200
Units
ps
MHz
ps
ps
ps
mV
12kHz-20MHz @ 500MHz
See Figure 3
600
–1.5
1.0
0.5
300
0.241
1
Common Mode Range
(10)
LVPECL_CLK
OE Set-Up Time
(11)
OE Hold Time
Output Rise/Fall Time
(20% to 80%)
–0.4
V
ns
ns
650
ps
10. V
CMR
is defined as the range within which the VIH level may vary with the device still meeting the propagation delay specification. The numbers in
the table are referenced to V
CCI
. The VIL level must be such that the peak-to-peak voltage is less than 1.0V and greater than or equal to V
PP
(min).
11. OE set-up time is defined with respect to the rising edge of the clock. OE HIGH-to-LOW transition ensures outputs remain disabled during the next
After successful initialization, the function aci_gap_create_connection is used to connect directly according to the address, but it returns 0x46 BLE_STATUS_NOT_ALLOWED. The connection cannot be succe...
Could you please give me some advice, is the communication between the computer and the microcontroller transmitted in the form of frames? How to package the frames? Is there a corresponding function?...
This Hyperbike is a tank among human-powered vehicles. When you ride it, you will never lose when it collides with a child's car. Of course, driving it requires the participation of all muscles in the...
Embedded systems are the replacement products of computer technology, communication technology, semiconductor technology, microelectronics technology, voice and image data transmission technology, and...[Details]
Introduction: Design of automated test systems
Challenges
To ensure the quality and reliability of products delivered to customers, test managers and engineers use automated test system...[Details]
In the development of high-stability lasers, real-time monitoring of the working state of the laser is an issue that needs to be focused on. This system realizes the high-stability laser temperatur...[Details]
JTAG Technology Introduction
One disadvantage of shrinking technology is that the complexity of testing small devices increases dramatically. When the board area is large, the board is tested...[Details]
AD8302
Introduction
AD8302 is a monolithic integrated circuit for RF/IF amplitude and phase measurement from ADI. It is mainly composed of two precisely matched broadband logarithmic det...[Details]
0 Introduction
SAA7111 is a programmable video processor produced by Philips. The chip integrates A/D and decoding functions. It has phase lock, automatic clamp, automatic gain control, cl...[Details]
Adding "intelligence" to measurement systems is becoming more common as 8-bit microcontrollers are inexpensive, widely available, and can be programmed using today's common high-level languages, su...[Details]
introduction
The fall detector is suitable for elderly people and children with poor self-care and self-protection abilities. It senses changes in the body posture of the individual wearing th...[Details]
summary
Theoretically explains how to set up a PFC boost regulator using a current sensing transformer with the UCC3817 control IC.
1. Schematic
The schematic diagram is show...[Details]
A well-designed electronic load is not designed just for use in the lab; it should be carefully designed and built to test actual power systems. This is true for military portable systems, such as ...[Details]
1. Introduction
The UCC28051 reference design is a 100W offline AC/DC voltage converter with power factor correction (PFC). This power module design is intended to illustrate how to proper...[Details]
Volkswagen's electronic throttle has taken our understanding of the traditional throttle a big step forward. However, while we admire Volkswagen's new technology, which is constantly being applied...[Details]
MIPS Technologies Inc. has introduced the CI10084tg, a next-generation global positioning system (GPS) RF tuner IP solution. The silicon-proven, integrated low-noise RF front end for GPS receivers...[Details]
0Introduction
As a service robot in the field of medical care, the application of smart wheelchairs makes extensive use of mobile robot technology. The key technologies involved in the researc...[Details]
TMS320C62X is a new generation of high-performance fixed-point digital signal processor (
DSP
) chip
from Texas Instruments (
TI
). The software design problem based on
DSP
is to use...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
