The reference level for the relative attenuation arel of the TFS 224C is the minimum of the pass band attenuation. This value is defined as the insertion
loss ae. The nominal frequency fN is fixed at 224,88 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole
operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme.
Data
Insertion loss
(reference level)
Nominal frequency
Passband
Pass band ripple
Relative attenuation
f
N
f
N
f
N
f
N
f
N
±
±
±
±
0,75
2,4
8
15
… f
N
MHz … f
N
MHz … f
N
MHz … f
N
MHz … f
N
±
±
±
±
±
0,3
2,4
8
15
50
arel
MHz
MHz
MHz
MHz
MHz
mean value in PB
ae
f
N
PB
typ. value
6,5
-
-
0,5
dB
f
N
dB
tolerance / limit
max.
9
224,88
±
0,3
1
dB
MHz
MHz
dB
max.
0,5
3,8
40
47
52
765
50
dB
dB
dB
dB
dB
ns
ns
max.
min.
min.
min.
min.
765
±
1
3
33
40
45
10
-
dB
dB
dB
dB
dB
ns
Group delay
Group delay ripple within PB
Deviation from linear phase
f
N
VSWR within PB
Operating temperature range
Storage temperature range
Frequency inversion temperature
Temperature coefficient of frequency
±
0,675 MHz
1,7
1,5 : 1
° rms
max.
max.
3,5
2:1
° rms
OTR
-
-
25
°C
ppm/K
2
- 30 °C ... + 80 °C
- 40 °C ... + 85 °C
-
-
TCf **
-0,03
*) The terminating impedances depend on parasites and q-values of matching elements and the board used, and are to be understood as reference
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**)
∆f(Hz)
= TCf(ppm/K²) x (∆T)² x fTo(MHz)
Generated:
Checked / Approved:
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail:
tft@telefilter.com
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Two wires are directly led out from the serial port and connected to the output port. Then they are connected to the computer serial port with wires. Can the voltage level be directly detected by the ...
Haha, look at this news, [size=10.5pt][url=http://www.expo-shandong.cn/news/gfxw/gfxw902.html][color=#800080]http://www.expo-shandong.cn/news/gfxw/gfxw902.html[/color][/url][/size][/size][/font] [font...
As far as I am concerned, the only true stupid thing you can do is not to be sure about something and don't dare to ask! Remember: the one that asks the question (might) look stupid for 5 minutes; the...
Hot summer, football passion. [flash]http://player.youku.com/player.php/sid/XNDMzNzk3ODcy/v.swf[/flash] This summer I participated in the labview training, and at the end I played a small ball footbal...
When debugging the program, I found that the received data is correct when running in single step, but the first part of the data is incorrect and the second part is correct when running continuously....
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Based on the actual situation, a remote intelligent anti-theft alarm device for home use, connected to the telephone line, simple to operate, and stable and reliable in operation is designed. When ...[Details]
1. Introduction
With the rapid development of computer technology, communication technology, and integrated circuit technology, the large-scale application of field control instruments and equ...[Details]
1. Fully understand the design requirements of all parties and determine the appropriate solution.
When starting a hardware development project, the original driving force will come from many a...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]