IMPORTANT NOTICE
Dear customer,
As from August 2
nd
2008, the wireless operations of NXP have moved to a new company,
ST-NXP Wireless.
As a result, the following changes are applicable to the attached document.
●
Company name - Philips Semiconductors
is replaced with
ST-NXP Wireless.
Copyright
- the copyright notice at the bottom of each page “© Koninklijke Philips
Electronics N.V. 200x. All rights reserved”, shall now read: “© ST-NXP Wireless 200x -
All rights reserved”.
Web site
-
http://www.semiconductors.philips.com
is replaced with
http://www.stnwireless.com
Contact information
- the list of sales offices previously obtained by sending an email
to
sales.addresses@www.semiconductors.philips.com,
is now found at
http://www.stnwireless.com
under Contacts.
●
●
●
If you have any questions related to the document, please contact our nearest sales office.
Thank you for your cooperation and understanding.
ST-NXP Wireless
www.stnwireless.com
ISP1301
Universal Serial Bus On-The-Go transceiver
Rev. 03 — 21 February 2006
Product data sheet
1. General description
The ISP1301 is a Universal Serial Bus (USB) On-The-Go (OTG) transceiver device that is
fully compliant with
Universal Serial Bus Specification Rev. 2.0
and
On-The-Go
Supplement to the USB Specification Rev. 1.0a.
The ISP1301 can transmit and receive
serial data at both full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) data rates.
It is ideal for use in portable electronics devices, such as mobile phones, digital still
cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio
players. It allows USB Application Specific Integrated Circuits (ASICs), Programmable
Logic Devices (PLDs) and any system chip set (with the USB host or device function
built-in but without the USB physical layer) to interface to the physical layer of the USB.
The ISP1301 can interface to devices with digital I/O voltages in the range of
1.65 V to 3.6 V.
The ISP1301 is available in HVQFN24 package.
2. Features
s
Fully complies with:
x
Universal Serial Bus Specification Rev. 2.0
x
On-The-Go Supplement to the USB 2.0 Specification Rev. 1.0a
x
On-The-Go Transceiver Specification (CEA-2011) Rev. 1.0
s
Can transmit and receive serial data at both full-speed (12 Mbit/s) and low-speed
(1.5 Mbit/s) data rates
s
Ideal for system ASICs or chip sets with built-in USB OTG dual-role core
s
Supports mini USB analog carkit interface
s
Supports various serial data interface protocols; transparent general-purpose buffer
mode allows you to control the direction of data transfer
s
Supports data line and V
BUS
pulsing session request
s
Contains Host Negotiation Protocol (HNP) command and status registers
s
Supports serial I
2
C-bus interface for OTG status and command controls
s
2.7 V to 4.5 V power supply input range for the ISP1301
s
Built-in charge pump regulator outputs 5 V at current greater than 8 mA
s
Supports external charge pump
s
Supports wide range interfacing I/O voltage (V
CC(I/O)
= 1.65 V to 3.6 V) for digital
control logics
Philips Semiconductors
ISP1301
USB OTG transceiver
s
8 kV built-in ElectroStatic Discharge (ESD) protection on the DP, DM, V
BUS
and ID
lines
s
Full industrial grade operation from
−40 °C
to +85
°C
s
Available in a small HVQFN24 (4
×
4 mm
2
) halogen-free and lead-free package
3. Applications
s
s
s
s
Mobile phone
Digital camera
Personal digital assistant
Digital video recorder
4. Ordering information
Table 1:
Ordering information
Package
Name
ISP1301BS
HVQFN24
Description
Version
plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; SOT616-1
body 4
×
4
×
0.85 mm
Type number
ISP1301_3
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 03 — 21 February 2006
2 of 51
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
