Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Note 1:
LX has internal clamp diodes to PGND and IN. Applications that forward bias these diodes should take care not to exceed
the IC’s package power dissipation limits.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 2)
TQFN
Junction-to-Ambient Thermal Resistance (
θ
JA
) ............36°C/W
Junction-to-Case Resistance (
θ
JC
).................................6°C/W
Note 2:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-
layer board. For detailed information on package thermal considerations, refer to
VS2008 uses Use MFC in a Static Library to generate ocx. It works well on WINCE, but it exits abnormally after changing to Use MFC in a Shared DLL. I guess the problem should be that a certain dll is ...
SIM300D can enable slow clock mode through AT+CSCLK=1, and then enter sleep mode, that is, slow clock mode, by pulling up the DTR pin. Now, without MUX started, the module can enter sleep mode, and th...
In addition, when running the program using evb programming, it shows that controls such as TreeView, Grid, etc. (non-ordinary controls) cannot be created. Thanks...
[b][url=http://www.deyisupport.com/question_answer/dsp_arm/c5000/f/48/t/141868.aspx]I would like to ask about the problem of writing the boot file of C5515 to the E2PROM of I2C[/url][/b][font=微软雅黑][si...
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Based on the actual situation, a remote intelligent anti-theft alarm device for home use, connected to the telephone line, simple to operate, and stable and reliable in operation is designed. When ...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
Abstract: A motion estimation design for video images is implemented using a powerful FPGA. The search method used is a three-step search method. When designing the scheme, this paper uses the rela...[Details]
Workers in garment factories usually turn on the power of the sewing machine motor as soon as they get to work and do not turn off the sewing machine power until they get off work. In fact, during ...[Details]
1 Introduction
Embedded touch screen device is a human-computer interaction device. Generally, the touch screen is installed on the LCD screen. The microprocessor is used to control the touch ...[Details]
1. Project Overview:
Changan Automobile Manufacturing Plant could produce 6 types of cars, with an annual output of about 80,000 vehicles. Its assembly line was manufactured in the late 19...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
