Operating Temperature Range ........................-55°C to +125°C
Junction Temperature ..................................................... +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
Soldering Temperature ....................................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= 2.7V to 5.5V, R
PULLUP
= 100kΩ, (open-drain output only), T
A
= -55°C to +125°C, unless otherwise noted. Typical values are
at T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage Range
SYMBOL
V
CC
Hot-temperature thresholds
(+35°C to +115°C)
Supply Current
I
CC
Cold-temperature thresholds
(-45°C to +15°C)
-15°C to +65°C
Temperature Threshold Accuracy
(Note 2)
Temperature Threshold
Hysteresis
HYST Input Threshold (Note 4)
Logic Output Voltage High
(Push-Pull)
Logic Output Voltage Low
(Push-Pull and Open Drain)
Open-Drain Output Leakage
Current
ΔT
TH
+75°C to +115°C
-45°C to -25°C (Note 3)
T
HYST
V
IH
V
IL
V
OH
V
OL
I
SOURCE
= 500µA, V
CC
> 2.7V
I
SOURCE
= 800µA, V
CC
> 4.5V
I
SINK
= 1.2mA, V
CC
> 2.7V
I
SINK
= 3.2mA, V
CC
> 4.5V
V
CC
= 2.7V, open-drain output = 5.5V
10
0.8 x V
CC
V
CC
- 1.5
0.3
0.4
HYST = V
CC
HYST = GND
0.8 x V
CC
0.2 x V
CC
-1.5
-2.5
-3
2
10
CONDITIONS
MIN
2.7
22
40
+1.5
+2.5
+3
°C
V
V
V
nA
°C
TYP
MAX
5.5
40
µA
UNITS
V
Note 1:
100% production tested at T
A
= +25°C. Specifications over temperature are guaranteed by design.
Note 2:
The MAX6514/MAX6515 are available with internal factory-programmed temperature trip thresholds from -45°C to +15°C
and +35°C to +115°C in 10°C increments.
Note 3:
V
CC
must be greater than 4.5V for a switching threshold of -45°C.
Usually, the characteristics of the amplifier are graphed using logarithmic frequency characteristics. How can we use a single-chip microcomputer to control an LCD to display this logarithmic frequenc...
[font=楷体_GB2312]——[color=navy]Written on the birth of [EEWORLD DIY] Oscilloscope V1.0. [/color][/font] "Our oscilloscope is born!" From yesterday to today, I have been silently repeating this sentence...
Typical application circuit diagram of TPS92310. You can find the information of TPS92310 on TI website. Here is an application circuit diagram for reference! ....
The automobile tire pressure monitoring system ( TPMS ) is mainly used to automatically monitor the tire pressure in real time while the car is driving, and to alarm for tire leakage and low pressure ...
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
