Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
µMAX
Junction-to-Ambient Thermal Resistance (θ
JA
) ......113.1°C/W
Junction-to-Case Thermal Resistance (θ
JC
) ................42°C/W
QSOP
Junction-to-Ambient Thermal Resistance (θ
JA
) ......103.7°C/W
Junction-to-Case Thermal Resistance (θ
JC
) ................37°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maxim-ic.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(V
CC
= 5V, V
GND
= 0V, MAX9925/MAX9927 gain setting = 1V/V, Mode A1, V
First of all, I would like to thank EEWORLD and administrator Orange Kai for giving me the chance to get TI's millimeter wave radar AWR1443EVM board for evaluation;
In actual use, the industry I work ...
After thinking for a long time, I don't know where to post it... I think I'll post it here... It's still necessary to learn ALLEGRO, so that you don't sit there in a daze when foreigners discuss this ...
Among them, there is a six-choice multi-channel analog chip select circuit on my baseboard. The six analog signals pass through the chip select chip, and only one is output, which is input to B7 of th...
I have a virtual serial port driver and the corresponding inf file. In the control panel, I can install it successfully through "Add Hardware" (XP system). I want to write my own installation program ...
[align=left][color=#000]I need help. I have a board with an AD7938 chip in Zone0 of the XINTF of the 28335 chip. I want to write data to the AD register through XD0-15. [/color][/align][align=left][co...
In order to prevent traffic accidents, when the intelligent detection device of the car detects danger ahead, it must send a warning message to the driver. The voice alarm clearly reminds the drive...[Details]
This article discusses how to use an ultra-low-power RF transceiver chip from Zarlink Semiconductor for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices to achiev...[Details]
The U.S. Food and Drug Administration (FDA) points out that home health care is the fastest growing area in the medical device industry. Driven by the increase in average life expectancy, the increasi...[Details]
1 Introduction
The integration of sensor technology and RFID has just started. As one of the world's major manufacturing and consumer countries, China should seize this opportunit...[Details]
Ultrasound systems are among the most sophisticated and complex signal processing instruments in widespread use today. Like any complex instrument, there are many trade-offs to be made in implement...[Details]
PCI (Perip heral Component Interconnect) is an advanced high-performance 32/64-bit local bus that supports linear burst transmission and has a maximum data transmission rate of 132MB/s. At the same...[Details]
0 Introduction to the direct method of feedback linearization based on dynamic equilibrium state theory
The basic idea of the direct method of feedback linearization based on dynamic equilib...[Details]
As mobile phones have evolved from simple voice communication tools to multimedia devices that integrate communication, imaging, and gaming, application processors are replacing baseband chips as t...[Details]
Compared with traditional light sources, light-emitting diodes (LEDs) have many advantages, such as low operating voltage, high energy efficiency, small size and directional light. They can provide...[Details]
1 Introduction
The intelligent meter reading system is a system that reads the data of multiple user meters in a centralized manner through the transmission media by the master station. It...[Details]
There are many ways to attenuate signals. The most commonly used method is to divide the voltage using resistors. The common circuits are as follows:
Oscilloscope pre-stage attenuation c...[Details]
Preface
In the analog era, due to the unchanged specifications and relatively simple device connections, as well as users' low requirements for image quality, the relatively simple environment...[Details]
In the issue of ensuring the safety of drivers and pedestrians, the proportion of electronic technology has increased. According to the survey, 80% to 90% of traffic accidents are caused by driver...[Details]
Most
embedded
systems are powered from a 48V backplane. This voltage is typically stepped down to a lower intermediate bus voltage of 24V, 12V, or 5V to power the circuit board racks withi...[Details]
Multimedia communication terminal equipment has a wide range of application prospects and can be applied to various fields such as video conferencing, videophone, PDA, digital television, etc. Therefo...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
