PH1-PLHLC3561 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-PLHLC3561

PH1-PLHLC3561: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-PLHLC3561 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-PLHLC3561 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	compliant
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Connection Type	LC/SPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Emitter/Detector Type	AVALANCHE PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1548 nm
Nominal optical power output	2.511 mW
minimum return loss	-27 dB
Sensitivity	-24 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Multifunctional display circuit

Hall integrated component AC motor on-off circuit diagram

Semiconductor component withstand voltage test circuit

Voltage-current conversion circuit

Circuit example circuit diagram (10A, 15V)

Long range body heat detector

Laser engraving machine modification: [i=s]This post was last edited by s23641017 on 2016-10-2 19:20[/i] I have a small CNC engraving machine and want to change it to a laser engraving machine. The stepper motor is 57 3A, the control boar...; s23641017 DIY/Open Source Hardware

How to get data from mpu6050 on msp430f5529 and how to define I2C: How to get data from mpu6050, how to define I2C...; 张晨 Microcontroller MCU

STM32 low power mode: Low Power Mode This article discusses the STM32 low power mode. First read the following manual.Comparing STM32F0 and STM32F1, they both enter low power consumption in the same way. There are three lo...; 可乐zzZ MCU

x Newcomer help: I am a novice and I have recently been learning according to the soc training materials, but I cannot install the 13th version of quartus in the textbook, so I installed the 15th version. When I used ...; lu112233 FPGA/CPLD

Comparison of several typical connection methods of optocoupler isolation in switching power supply: In general isolated power supplies, optocoupler isolated feedback is a simple and low-cost method. However, there has been no in-depth research on the various connection methods and differences of opt...; qwqwqw2088 Analogue and Mixed Signal

DSP Programming--5.31--Hardware Interrupt Management: [size=4]In order to correctly respond to hardware interrupts and for the stability of the DSP/BIOS kernel, please pay special attention to the following points when writing HWI hardware ISRs: [/size] ...; Jacktang DSP and ARM Processors

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components