If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Tolerance (Note 2)
Differential Input Voltage
Voltage at Input/Output Pin
Supply Voltage (V
+
–V
−
)
Current at Input Pin (Note
7)
Current at Output Pin
(Notes 3, 8)
Current at Power Supply
Pin
Lead Temperature
(soldering, 10 sec)
260˚C
2 kV
(V
CC
) +0.3V to (−V
CC
)−0.3V
(V
CC
) + 0.3V to
(−V
CC
)−0.3V
16V
Storage Temperature
Range
Junction Temperature
(Note 4)
−65˚C to +150˚C
150˚C
Operating Ratings
(Note 1)
Supply Voltage
Junction Temperature Range
LMC7211AI, LMC7211BI
Thermal Resistance (θ
JA
)
SO-8 Package,
8-Pin Surface Mount
M05A Package,
5-Pin Surface Mount
180˚C/W
325˚C/W
2.7
≤
V
CC
≤
15V
−40˚C
≤
T
J
≤
+85˚C
±
5 mA
±
30 mA
40 mA
2.7V Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 2.7V, V
−
= 0V, V
CM
= V
O
= V+/2.
Boldface
limits apply
at the temperature extremes.
Typ
Symbol
V
OS
TCV
OS
Parameter
Input Offset Voltage
Input Offset Voltage
Temperature Drift
Input Offset Voltage
Average Drift
I
B
I
OS
CMRR
PSRR
A
V
CMVR
Input Current
Input Offset Current
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Voltage Gain
Input Common-Mode
Voltage Range
CMRR
>
55 dB
V
OH
V
OL
I
S
Output Voltage High
Output Voltage Low
Supply Current
I
load
= 2.5 mA
I
load
= 2.5 mA
V
OUT
= Low
−0.3
2.5
0.2
7
CMRR
>
55 dB
100
3.0
2.9
2.7
−0.2
0.0
2.4
2.3
0.3
0.4
12
14
2.9
2.7
−0.2
0.0
2.4
2.3
0.3
0.4
12
14
dB
V
min
V
max
V
min
V
max
µA
max
2.7V
≤
V
+
≤
15V
80
dB
0V
≤
V
CM
≤
2.7V
0.04
0.02
75
pA
pA
dB
(Note 10)
3.3
µV/Month
Conditions
(Note 5)
3
1.0
LMC7211AI
Limit
(Note 6)
5
8
LMC7211BI
Limit
(Note 6)
15
18
mV
max
µV/˚C
Units
www.national.com
2
LMC7211
5.0V and 15.0V Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5.0V and 15V, V
−
= 0V, V
CM
= V
O
= V
+
/2.
Boldface
lim-
its apply at the temperature extremes.
Typ
Symbol
V
OS
TCV
OS
Parameter
Input Offset Voltage
Input Offset Voltage
Temperature Drift
Input Offset Voltage
Average Drift
I
B
I
OS
CMRR
PSRR
A
V
CMVR
Input Current
Input Offset Current
Common Mode
Rejection Ration
Power Supply
Rejection Ratio
Voltage Gain
Input Common-Mode
Voltage Range
V+ = 5.0V
CMRR
>
55 dB
V+ = 5.0V
CMRR
>
55 dB
V+ = 15.0V
CMRR
>
55 dB
V+ = 15.0V
CMRR
>
55 dB
V
OH
Output Voltage High
V+ = 5V
I
load
= 5 mA
V+ = 15V
I
load
= 5 mA
V
OL
Output Voltage Low
V+ = 5V
I
load
= 5 mA
V+ = 15V
I
load
= 5 mA
I
S
I
SC
Supply Current
Short Circuit Current
V
OUT
= Low
Sourcing
Sinking (Note 8)
7
30
45
0.2
0.2
14.8
4.8
−0.3
15.3
−0.3
100
5.3
5.2
5.0
−0.2
0.0
15.2
15.0
−0.2
0.0
4.6
4.45
14.6
14.45
0.40
0.55
0.40
0.55
14
18
5.2
5.0
−0.2
0.0
15.2
15.0
−0.2
0.0
4.6
4.45
14.6
14.45
0.40
0.55
0.40
0.55
14
18
dB
V
min
V
max
V
min
V
max
mV
min
mV
min
mV
max
mV
max
µA
max
mA
mA
V+ = 5.0V
V+ = 15.0V
5V
≤
V
+
≤
10V
V = 5V
V
+
= 15V
V = 5V
V
+
= 15V
+
+
LMC7211AI
Limit
(Note 6)
5
8
LMC7211BI
Limit
(Note 6)
15
18
mV
max
µV/˚C
µV/Month
pA
pA
dB
dB
dB
Units
Conditions
(Note 5)
3
1.0
4.0
3.3
4.0
0.04
0.02
75
82
80
AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5V, V
−
= 0V, V
CM
= V
O
= V
+
/2.
Boldface
limits apply at
the temperature extreme.
Typ
Symbol
t
rise
t
fall
Parameter
Rise Time
Fall Time
Conditions
f = 10 kHz, Cl = 50 pF,
Overdrive = 10 mV (Note 9)
f = 10 kHz, Cl = 50 pF,
Overdrive = 10 mV (Note 9)
0.3
µs
(Note 5)
0.3
LMC7211AI
Limit
(Note 6)
LMC7211BI
Limit
(Note 6)
µs
Units
3
www.national.com
LMC7211
AC Electrical Characteristics
(Continued)
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5V, V
−
= 0V, V
CM
= V
O
= V
+
/2.
Boldface
limits apply at
the temperature extreme.
Typ
LMC7211AI
Limit
(Note 6)
LMC7211BI
Limit
(Note 6)
µs
Units
Parameter
Propagation Delay
(High to Low)
(Note 11)
f = 10 kHz,
Cl = 50 pF
(Note 9)
V+ = 2.7V,
f = 10 kHz,
Cl = 50 pF
(Note 9)
10 mV
100 mV
10
4
µs
Conditions
10 mV
100 mV
(Note 5)
10
4
Symbol
t
PHL
t
PLH
Propagation Delay
(Low to High)
(Note 11)
f = 10 kHz,
Cl = 50p
(Note 9)
V+ = 2.7V,
f = 10 kHz,
Cl = 50 pF
(Note 9)
10 mV
100 mV
10 mV
100 mV
6
4
7
4
µs
µs
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2:
Human body model, 1.5 kΩ in series with 100 pF.
Note 3:
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150˚C. Output currents in excess of
±
30 mA over long term may adversely affect reliability.
Note 4:
The maximum power dissipation is a function of T
J(max)
,
θ
JA
, and T
A
. The maximum allowable power dissipation at any ambient temperature is
P
D
= (T
J(max)
− T
A
)/θ
JA
.All numbers apply for packages soldered directly into a PC board.
Note 5:
Typical values represent the most likely parametric norm.
Note 6:
All limits are guaranteed by testing or statistical analysis.
Note 7:
Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage rating.
Note 8:
Do not short circuit output to V+, when V+ is greater than 12V or reliability will be adversely affected.
Note 9:
C
L
includes the probe and jig capacitance.
Note 10:
Input offset voltage average drift is calculated by dividing the accelerated operating life V
OS
drift by the equivalent operational time. This represents worst
case input conditions and includes the first 30 days of drift.
Note 11:
Input step voltage for propagation delay measurement is 2V.
[i=s]This post was last edited by Jizhibao on 2016-9-2 14:26[/i] [font="]Wifi firmware airborne: Qualcomm QCA4004, Espressif ESP8266, RealTek_8711AM,[/font] [font="]As long as you develop an MCU, you ...
I made a DDS board, and soldered two DAs and filters just in case (MAX5884 is used for DA), but both channels cannot output normally. The sine wave output by one channel has noise and serious clutter....
Application of three-phase SPWM generator SA8282 in static inverterWith the continuous development of power electronics technology and the continuous updating of power electronics products, pulse widt...
I recently applied for an embedded software engineer position. Since most people know about common technical knowledge, I will not describe it here. Instead, I have sorted out other interview experien...
What do you think of the efficiency of VDSP's compiled code? Why do I feel that the efficiency of C language compiled code is very low? Although compiler optimization is enabled, there are few paralle...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
