EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLAFC3761

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GLAFC3761 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,

PH1-GLAFC3761 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1552 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Can't discuss today?
What happened?!...
hk6108 Analog electronics
Code reading and firmware reinstallation
[i=s]This post was last edited by WZH70246 on 2017-3-1 21:46[/i]Official source code and development document URL: [url=http://www.st.com/content/st_com/en/products/evaluation-tools/solution-evaluatio...
WZH70246 ST Sensors & Low Power Wireless Technology Forum
About the digital tube
There is a question that requires this: use a button to control the digital tube count. Each time the button is pressed, 1 is added, from 00 to 99. After reaching 99, the button returns to 00, and the...
yuewei167 Embedded System
Ask about the FLASH download problem of F2812
The first time I downloaded the program to the 2812 FLASH, it was successful and the program could be executed. After erasing the next day, the download failed and reported:Flash API Error #31:There w...
paulguo Microcontroller MCU
Hiring R&D engineers with integrity
[b]Honestly recruiting R&D engineers[/b] Our company produces medical electronic related equipment and cooperates with universities for R&D. We are now recruiting 1-2 R&D engineers. The main job is to...
viewmed Recruitment
The problem of LM393 not outputting square waves in applications
I used LM393, but I used a board made with this principle. There was no problem with the output signal of a previous board, but the output voltage of LM393 on this board is 0V, 1.25V, and 5V. It only ...
caesar1980 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 720  1032  2824  960  1633  15  21  57  20  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号