REVISIONS
LTR
A
B
DESCRIPTION
Changes in accordance with NOR 5962-R177-96.
Drawing updated to reflect current requirements. Redrawn. - ro
DATE (YR-MO-DA)
96-07-10
05-05-02
APPROVED
M. A. FRYE
R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
B
1
B
2
B
3
B
4
B
5
B
6
B
7
B
8
PREPARED BY
DONALD R. OSBORNE
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D. A. DiCENZO
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
APPROVED BY
N. A. HAUCK
DRAWING APPROVAL DATE
87-05-27
MICROCIRCUIT, LINEAR, LOW NOISE
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
AMSC N/A
REVISION LEVEL
B
SIZE
A
SHEET
CAGE CODE
14933
1 OF
8
5962-86887
DSCC FORM 2233
APR 97
5962-E294-05
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-86887
01
C
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
OP-227A
Circuit function
Dual, low-offset, low noise operational amplifier
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
C
Descriptive designator
GDIP1-T14 or CDIP2-T14
Terminals
14
Package style
Dual-in-line
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings. 1/
Supply voltage (V
CC
) ..............................................................
±22
V dc
Input voltage range (V
IN
) ........................................................
±22
V dc
Output short circuit duration .................................................... Indefinite
Differential input current ..........................................................
±25
mA 2/
Differential input voltage range ...............................................
±0.7
V dc
Lead temperature (soldering, 60 seconds) ............................. +300°C
Storage temperature range ..................................................... -65°C to +150°C
Maximum power dissipation (P
D
) ............................................ 500 mW 3/
Thermal resistance, junction-to-case (
θ
JC
) ............................. See MIL-STD-1835
1.4 Recommended operating conditions.
Supply voltage (V
CC
) ..............................................................
±4.5
V dc to
±18
V dc
Ambient operating temperature range (T
A
) ............................. -55°C to +125°C
______
1/ Unless otherwise specified, all voltages are referenced to ground.
2/ The inputs are protected by back-to-back diodes. Current limiting resistors are not used in order to achieve low noise.
If differential input voltage exceeds
±0.7
V, the input current should be limited to 25 mA.
3/ For T
A
greater than 106°C, derate linearly at 11.3 mW/°C.
SIZE
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
A
REVISION LEVEL
5962-86887
SHEET
B
2
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or
http://assist.daps.dla.mil
or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections and logic diagram. The terminal connections and logic diagram shall be as specified on
figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
SIZE
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
A
REVISION LEVEL
5962-86887
SHEET
B
3
TABLE I. Electrical performance characteristics.
Conditions
-55°C
≤
T
A
≤
+125°C
±V
S
=
±15
V
unless otherwise specified
Input offset voltage
V
IO
1
2,3
Input offset current
I
IO
1
2,3
Input bias current
I
IB
1
2,3
Average input offset
drift
Power supply rejection
ratio
Common mode rejection
ratio
Large signal voltage gain
1/
TC V
IO
PSRR
V
S
=
±4
V to
±18
V
1,2,3
1
2,3
CMRR
V
CM
=
±11
V
V
CM
=
±10
V
A
VOL
V
O
=
±10
V, R
L
≥
2 kΩ
1
2,3
4
5,6
V
O
=
±10
V, R
L
≥
600
Ω
Input voltage range
IVR
T
A
= +25°C
T
A
= -55°C, +125°C 1/
Output voltage swing
V
OP
R
L
≥
2 kΩ
4
1
2,3
4
5,6
R
L
≥
600
Ω
Slew rate
Input noise voltage density
SR
E
n
R
L
≥
2 kΩ, T
A
= +25°C
f
O
= 10 Hz, T
A
= +25°C
f
O
= 1,000 Hz,
T
A
= +25°C
Input noise current density
I
n
f
O
= 10 Hz, T
A
= +25°C
f
O
= 1,000 Hz,
T
A
= +25°C
See footnotes at end of table.
7
01
5.66
0.99
pA /
Hz
4
7
7
01
01
01
01
01
01
114
108
1000
600
800
±11.0
±10.0
±12
±11.5
±10
1.7
6.0
3.9
V/µs
nV /
Hz
V
V
V/mV
01
01
01
01
01
Test
Symbol
Group A
subgroups
Device
type
Min
Limits
Unit
Max
80
180
35
50
40
60
1.0
10
16
dB
µV/°C
µV/V
nA
nA
µV
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86887
SHEET
B
4
TABLE I. Electrical performance characteristics – Continued.
Conditions
-55°C
≤
T
A
≤
+125°C
±V
S
=
±15
V
unless otherwise specified
Gain bandwidth
product
Power consumption
Input offset voltage match
1/
GBW
P
D
V
OS
f = 100 kHz, T
A
= +25°C
Each amplifier,
T
A
= +25°C
T
A
= +25°C
T
A
= -55°C, +125°C
Average noninverting
bias current
I
B+
I
B+
= ( I
B+A
+ I
B+B
) / 2,
T
A
= +25°C
I
B+
= ( I
B+A
+ I
B+B
) / 2,
T
A
= -55°C, +125°C
Noninverting offset current
I
OS+
I
OS+
= ( I
B+A
- I
B+B
),
T
A
= +25°C
I
OS+
= ( I
B+A
- I
B+B
),
T
A
= -55°C, +125°C
Inverting offset current
I
OS-
I
OS-
= ( I
B-A
- I
B-B
),
T
A
= +25°C
I
OS-
= ( I
B-A
- I
B-B
),
T
A
= -55°C, +125°C
1/ Guaranteed if not tested.
2,3
±90
1
01
±60
nA
2,3
±90
1
01
±60
nA
2,3
±60
1
2,3
1
01
01
80
180
±40
nA
µV
4
1
01
01
Test
Symbol
Group A
subgroups
Device
type
Min
5.0
Limits
Unit
Max
MHz
140
mW
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86887
SHEET
B
5
京公网安备 11010802033920号
EEWORLD
