EEWORLDEEWORLDEEWORLD

Part Number

Search

2-641216-6

Description
HEADER CONNECTOR,PCB MNT,RECEPT,26 CONTACTS,PIN,0.1 PITCH,R ANGLE PC TAIL TERMINAL,POLARIZED LCK,NATURAL
CategoryThe connector    The connector   
File Size67KB,1 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

2-641216-6 Overview

HEADER CONNECTOR,PCB MNT,RECEPT,26 CONTACTS,PIN,0.1 PITCH,R ANGLE PC TAIL TERMINAL,POLARIZED LCK,NATURAL

2-641216-6 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompli
body width0.225 inch
subject depth0.1 inch
body length2.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact resistance5 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage750VAC V
Insulation resistance5000000000 Ω
Insulator colorNATURAL
insulator materialPOLYESTER
Manufacturer's serial number641216
Plug contact pitch0.1 inch
Installation option 1POLARIZED LCK
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)4 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.04 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts26
Base Number Matches1
McAsp multi-channel understanding
[i=s]This post was last edited by fish001 on 2019-3-10 15:24[/i] [align=left][color=rgb(85, 85, 85)][size=14px]Due to project needs, I started to look at the McAsp interface. This is my first time to ...
fish001 DSP and ARM Processors
Can anyone tell me if it is possible to get I2C from a TI Sensortag?
Can any kind person see if it is possible to lead out I2C from TI Sensortag? I looked at the PDF document of Sensortag's PCB last night. It is a four-layer board. It is difficult to compare. I used tw...
wangfuchong Wireless Connectivity
Please ignore the points
Just for points...
bg7jw Embedded System
Strange problem when compiling bootrom under DOS: undefine reference `statSymTbl' "_ctor" "_dtor" `usrBreakpoint
: I used make bootrom.bin to compile BOOTROM in dos, but a lot of things that were not included in my BSP appeared. D:\Tornado2.2MIPS\target\config\incaip2Demo_warrior>make bootrom ccmips -c -G 0 -mno...
laoyuyin Embedded System
AT89C52 Network Interface Diagram
SHT10,CS8900,AT89C52,YL18-1080S...
klanlan Embedded System
How does the SG3525 push-pull output generate the desired DC voltage?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:34[/i] As shown in the figure, I don't understand how the voltage output at pins 11 and 14 generates 12V and +-15V voltages through the trans...
adc Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1195  333  1706  1170  951  25  7  35  24  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号