(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .......................................................... 65°C to +150°C
Note:
Stresses greater than those listed under MAXIMUM
Ambient Temperature with Power Applied .......................... 40°C to +85°C
RATINGS may cause permanent damage to the
Supply Voltage to Ground Potential (Inputs & Vcc Only) ........ 0.5V to +7.0V device. This is a stress rating only and functional
Supply Voltage to Ground Potential (Outputs & D/O Only) ..... 0.5V to +7.0V operation of the device at these or any other conditions
above those indicated in the operational sections of
DC Input Voltage ................................................................... 0.5V to +7.0V
this specification is not implied. Exposure to absolute
DC Output Current ............................................................................. 120mA maximum rating conditions for extended periods may
Power Dissipation ................................................................................. 0.5W affect reliability.
DC Electrical Characteristics
(Over the Operating Range, T
A
= 40°C to +85°C, V
CC
= 5V ±5%)
Parameters Description
V
IH
V
IL
I
IH
I
IL
I
OZH
V
IK
I
OS
V
H
R
ON
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
Short Circuit Current
(3)
Input Hysteresis at Control Pins
Switch On Resistance
(4)
V
CC
= Min., V
IN
= 0.0V, I
ON
= 48mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
Test Conditions
(1)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
CC
= Max., V
IN
= V
CC
V
CC
= Max., V
IN
= GND
0 A, B V
CC
V
CC
= Min., I
IN
= 18mA
A (B) = 0V, B (A) = V
CC
100
150
5
10
7
15
0.7
Min.
2.0
0.5
0.8
±1
±1
±1
1.2
V
mA
m
V
ohm
µA
Typ
(2)
Max.
Units
V
Capacitance
(T
A
= 25°C, f = 1 MHz)
Parameters
(5)
C
IN
C
OFF
C
ON
Description
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
Test Conditions
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
Typ
Max.
6
6
8
Units
pF
Notes:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the
applicable device type.
2. Typical values are at V
CC
= 5.0V, T
A
= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
Shuhai Education’s “FPGA Training Class Course Information” Shanghai Shuhai Education’s FPGA training class will start soon: For the course content of Shuhai Education’s “FPGA Application Design Eleme...
Embedded systems are one of the fastest growing segments of today's computer industry. As the number of devices using embedded computer systems increases, programmers, hobbyists, and engineers of all ...
https://bbs.eeworld.com.cn/thread-233084-1-1.html
https://bbs.eeworld.com.cn/thread-233077-1-1.htmlEveryone knows that the touching people activity of the forum is divided into moderators and forum me...
[i=s]This post was last edited by littleshrimp on 2020-3-25 12:46[/i]STEVAL-MKI109V3 can be directly connected to the LIS25BA sensor to collect audio data
You can see real-time data changes through Un...
Use LPC2478 in ARM7 to design a communication chip, Ethernet to serial port, to make the chip run. At least include those parts, and give a simple introduction to the following design process, and it ...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
In order to develop lighting LED technology, developed countries attach great importance to the research of LED testing methods and standards. For example, the National Institute of Standards and T...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
0 Introduction
In microwave, radar, radio and television, and communication systems, the problem of coupling RF power is often encountered. A directional coupler is a directional power divide...[Details]
When programming in C and assembly, there are interface issues between variables and functions in C and assembly.
Variables defined in a C program are put into the .bss area after being compile...[Details]
Liquid crystal displays are increasingly widely used in pocket instruments and low-power application systems due to their advantages of low power consumption, small size, rich display content, and ...[Details]
Thyristor is the abbreviation of thyristor, commonly known as silicon controlled rectifier. It is a high-power switching semiconductor device, represented by the letter symbols "V" or "VT" in the c...[Details]
The construction of voltage and current feedback amplifier application circuits is generally the same, except for a few key points.
Current feedback amplifiers have higher sl...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
