EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-410-72-0850R

Description
Board Connector, 144 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-410-72-0850R Overview

Board Connector, 144 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle

54122-410-72-0850R Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.335 inch
body length7.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts144
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
About ADXL203 to measure tilt angle
When using ADXL203 to measure the tilt angle, the output should be 2.5V at 0° and 3.5V at 90°. The outputs I measured in the experiment were 2.5038V and 3.509V, which are basically correct. However, s...
lene ADI Reference Circuit
Use jlink to download the program to stm32, the jlink red light flashes, and finally the microcontroller cannot be recognized
When using jlink's sw mode to download the program, the debug window cannot recognize the MCU. jlink can be downloaded normally on other boards, so there is no problem with jlink, and there is no prob...
研究深 stm32/stm8
How can I create a WINCE emulator running on a PC with an ARMV4I CPU?
How can I use PB to create a WINCE simulator with ARMV4I CPU running on PC? Just explain the key steps. It seems that I cannot select two CPUs. If I select X86 and ARMV4I, there is no corresponding si...
bbs_cq Embedded System
My wireless network is not working, the driver is fine, it was working yesterday but not today
My laptop is ASUS x50sl. It was working fine yesterday, but not today. I installed the system and drivers, but still can't get on, and reports this error: Name: Association test Description: This test...
6562748 Embedded System
Request Wince system customization information
Who has more detailed information about Wince system customization? Can you send me a copy? My email: baiminshengbai@126.com Send me a message and I will give you a copy. Thank you...
heater Embedded System
How to implement a power switch similar to a mobile phone
From EEWORLD cooperation group: arm linux fpga embedded 0 (49900581) That is: long press the button to turn it on and off. Now it is realized by adding a trigger and a power IC, but the effect is not ...
小天 Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2534  190  607  639  2394  52  4  13  49  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号