The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
High-Speed (3.125Gbps) Stacking Connectors
FX8C Series
sMechanical
features
q
0.6mm Pitch
q
Stacking Height : 5~16mm
q
Number of Contacts : 60, 80, 100, 120, 140,
q
SMT Coplanarity
q
Mating Guide
160, 200, 240, 280
The coplanarity of the SMT solder area lead is
maintained at the high accuracy of less than 0.1mm.
The very small and guide rib is provided, and secures
±0.6mm self-alignment, considering the mating
operativity into accounts. ( fig.1 )
2
Effective Mating Length
fig.1
H
+0.3
-0.2
q
Effective Mating Length : 2mm ( fig.1 )
q
Mis-insertion Prevention
q
Two-piece Connection Product
The boss prevents mis-insertion in the board to cause
due to the boss position and boss diameter.
In order to enhance the mating reliability for fine pitch
connector using two-pieces, the two-pieces of
connectors are combined by our unique method, and
can secure the mount position accuracy. In such a
new concept, the two-piece connected product is
prepared at every number of contacts ( The standard
mating pitch for the two-piece interconnected product
in two rows is 11mm. )
H:Stacking Height
0.6
0.6
s
Signal integrity features
q
Insertion-Loss-to-Crosstalk-Ratio ( ICR )
The insertion-loss-to-crosstalk ratio (ICR) with
five-aggressor differential FEXT meets the IEEE
802.3ap specification for 3.125
+
Gbps with plenty
of margins.
The differential impedance is within 100±10 ohms
at 100 ps rise time (20% to 80%).
q
Differential Impedance
s
Stacking height variations (5mm~16mm)
Receptacle
Header
FX8C-**P-SV
FX8C-** / **P11-SVJ
FX8C-**P-SV1
FX8C-** / **P11-SV1J
FX8C-**P-SV2
FX8C-**/**P11-SV2J
FX8C-**P-SV4
FX8C-** / **P11-SV4J
FX8C-**P-SV6
FX8C-** / **P11-SV6J
FX8C-**S-SV
FX8C-** / **S11-SVJ
5mm
6mm
7mm
9mm
11mm
FX8C-**S-SV5
FX8C-** / **S11-SV5J
10mm
5∼16
11mm
12mm
14mm
16mm
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
5.
Humidity (Steady state)
Contact resistance: 100m
ohms
max.Insulation resistance: 100M
ohms
min.
96 hours at temperature of 40 ± 2ç and humidity of 90% to 95%
Contact resistance: 100m
ohms
max.Insulation resistance: 100M
ohms
min. (-55ç: 30 minutes, 15
to
35ç: 2
to
3 minutes
(-85ç:
30 minutes, 15
to
35ç: 2
to
3minutes) 5 cycles
7. Durability (Mating/un-mating) Contact resistance: 100m
ohms
max.
50 cycles
8. Resistance to Soldering heat
No deformation of components affecting performance. Reflow: At the recommended temperature profile
Manual soldering: 360ç for 5 seconds
Note 1 : Includes temperature rise caused by current flow.
Note 2 : The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
Note 3 : Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.
Note 4 : FX8C-*P-SV(*),FX8C-*S-SV(*) is gold plated.
Note 5 : Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a
specific part number shown.
sMaterial
Part
Insulator
Header Contact
Receptacle Contact
Material
PPS
Phosphor bronze
Phosphor bronze
Finish
Light brown
Contact area
Lead area
Contact area
Lead area
Gold plated
Tin plated(Note 4)
Gold plated
Tin plated(Note 4)
Remarks
UL94V-0
–––––––
–––––––
sOrdering
Information
qSingle
Product
FX8C
q
- 120 P - SV 1 (91)
w
e
r
t
y
t
Product height variation Blank : Standard (Minimum low profile)
1:
+1mm
. . . . . . 6:+6mm
y
Packaging Type
(71) : Tray packaging
(91) : Tube packaging
(92) : Embossed tape package
q
Series Name : FX8C
w
Number of Contacts :60, 80, 100, 120, 140
e
Connector type
r
Contact type
P :Header
S :Receptacle
SV :Board vertical type
qtwo-piece
Connection Product
FX8C
q
- 120/120 P 11 - SV 1 J
w
e
r
t
y u
r
Connector to Connector Pitch
t
Contact type
SV : Board vertical type
y
Product Height VariationBlank : Standard (Minimum lot profile)
1:+1mm . . . . . . 6:+6mm
u
J: two-piece connection product
q
Series Name :FX8C
w
Number of Contacts: 60∞2, 80∞2, 100∞2,
120∞2, 140∞2
Example: 120/120 = 240 contacts
e
Connector Type :
P : Header
S : Receptacle
*The
standard packaging of the two-piece connection product is the tray packaging.
10
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
To match 100 ohm differential impedance and to reduce crosstalk, a staggered GSGSG pin assignment is recommended for
FX8C of 5mm to 9mm height, and a staggered GSSG pin assignment is recommended for 10mm to 16mm height. (G=ground
and S=signal)
GSGSG
GSSG
signal
ground
q
Impedance
The differential impedance is 100 ± 10 ohm for FX8C of 5mm and 16mm height at 100 ps rise time (20% to 80%).
5mm
16mm
q
Propagation delay
The propagation delay is 69 and 118 ps for FX8C of 5mm and 16mm height, respectively.
q
Insertion loss
The differential insertion loss crosses 1 dB at 7 and 5 GHz for FX8C of 5mm and 16mm height, respectively.
5mm
16mm
11
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
The differential return loss meets the IEEE 802.3ap specification to 10 and 7 GHz for FX8C of 5mm and 16mm height,
respectively.
5mm
16mm
q
Near-end crosstalk (NEXT)
The staggered GSGSG and GSSG pin assignments resulted in low differential NEXT.
5mm
16mm
12
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
The STEVAL-IDB008V1M Bluetooth development board is similar to the STEVAL-IDB008V1. The STEVAL-IDB008V1M uses the BlueNRG-M2SA Bluetooth module. The BlueNRG-M2SA module uses the BlueNRG-2 Bluetooth ch...
I graduated in 2004 with a major in Computer Science and Technology. I am currently working in Nanshan District, Shenzhen. The company is owned by a Hong Kong boss and has more than 100 employees. My ...
NETIO is a relatively simple network testing tool. The specific address is as follows [url]http://www.nwlab.net/art/netio/netio.html[/url]I added it to rawos to test the performance of the underlying ...
The serial port is one of the most commonly used functions of MCU. It can be used to input and output debugging information. SS5 comes with many routines, which are super convenient and smooth to use....
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
In the 1980s, breakthroughs were made in the design and production of small, low-power quartz metal halide lamps with precise dimensions. At the same time, with the acceleration of people's lives a...[Details]
1. Basic principles of organic/polymer solar cells
The basic principle of organic/polymer solar cells is to use the photovoltaic effect generated by light incident on the heterojunction of sem...[Details]
Button cells (also called button cells) are those batteries with equal or larger diameter and height. The current size range of alkaline button cells is specified as follows: diameter 4.8mm-11.4mm,...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
_pdf/pg_0001.png)
ST - Low Power RF
京公网安备 11010802033920号
EEWORLD_pdf/1.png)
_pdf/2.png)
_pdf/3.png)
_pdf/4.png)
_pdf/5.png)
_pdf/pg_0002.png)
_pdf/pg_0003.png)
_pdf/pg_0004.png)
_pdf/pg_0005.png)
