The structure of longer electrodes provides the wider welding area than the chip resistors with normal electrodes,
and this enhanced the solder welding strength.
2) Increased surge-resistance
This is achieved by Rohm’s original trimming technology plus resistive element patterning.
3) High-power tolerance
Two times of the rated power is guaranteed than the normal-electrode resistors.
4) ROHM resistors are ISO-9001 & ISO/TS16949 certified.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using
or ordering it.
Applications
Automotive, industrial and power supply.
Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
POWER LOAD (%)
Specifications
0.5W (1 /2W)
at 70°C
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (
°
C)
Fig.1
Rated voltage
Rated current
The voltage rating is calculated by the following equation.
E=
I =
P
×
R
P/R
E : Rated voltage (V)
I : Rated current (A)
P : Rated power (W)
R : Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55°
C to
+ 155°C
1/4
LTR10
Resistors
Table 1
Resistance range
(Ω)
Resistance
tolerance
F (±1%)
J (±5%)
Special part number
Resistance temperature coefficient
(ppm/°C)
0.047
0.1
R
R
10
0.1
S
L
±150
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Characteristics
Item
Guaranteed value
Resistor type
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Voltage : A
Measuring method : Measure under termination by 4 probes
Under termination
Terminal
Resistance
F :
±1%
J :
±5%
Variation of resistance
with temperature
See Table.1
JIS C 5201-1 4.8
Measurement :
−55
/
+25
/
+125°C
JIS C 5201-1 4.13
Rated voltage (current)
×
2.5, 2s.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. :
−55°C
to
+125°C
5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON
−
0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
155°C
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
Overload
±
(2.0%+0.1Ω)
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±
(1.0%+0.005Ω)
No remarkable abnormality on the appearance.
±
(1.0%+0.005Ω)
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
±
(3.0%+0.005Ω)
Endurance at 70°C
±
(3.0%+0.005Ω)
Endurance
±
(3.0%+0.005Ω)
Resistance to solvent
Bend strength of
the end face plating
±
(0.5%+0.005Ω)
Without open.
2/4
LTR10
Resistors
Dimensions
(Unit : mm)
W
a
R033
b
L
3
2
4
5
1
No.
1
2
3
7
4
5
6
Material
Resistive element
Silver thick film electrode
Silver thick film side electrode
Nickel electrode
Sn electrode
Overcoating
Alumina substrate
L
6
t
Size code
2012 (0805)
L
1.2
±
0.1
W
2.0
±
0.1
t
0.55
±
0.1
a
0.35
±
0.1
b
0.25
±
0.1
7
Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
W
08
06
04
02
02
04
06
08
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
mount
T
2
C
Label
EIAJ ET-7200B compliant
(Unit: mm)
(Unit: mm)
A
φ180
0
−1.5
B
φ60
+1
0
9
C
+1.0
0
D
φ13±0.2
W
8.0±0.3
D
0
+0.1
φ1.5
0
F
3.5±0.05
P
0
4.0±0.1
E
1.75±0.1
P
1
4.0±0.1
A
0
1.65
+0.2
−0.1
B
0
2.4
+0.2
−0.1
P
2
2.0±0.05
T
2
Max. 1.1
3/4
LTR10
Resistors
Part designation
L T R 1 0
Part No.
E Z P
J
F
J
±
5%
±
1%
L
Nominal resistance
Resistance code, 3 or 4 digits.
Resistance tolerance
Resistance
tolerance
J
F
:
:
Resistance
code
3 digits
4 digits
Packaging Specifications Code
Part No.
LTR10
Code
EVH
Resistance tolerance
F(
±
1%)
J(
±
5%)
Packaging specifications
Paper tape (4mm Pitch)
Reel
φ180mm
(7inch)
Basic ordering unit
(pcs)
5,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
I have a friend who uses dsp. Recently, he has some problems that he cannot solve. Please help me. Thank you very much! He uses this chip: TMS320LF2407APGEA. The specific problem is as follows: When w...
[size=4]I did a PLC experiment in the afternoon and only had time to post a thread in the evening! [/size][size=5][color=red][b]Upload the complete project as usual:Demo video: [media=x,500,375]http:/...
Code element simulation analysis Because the transmission rate of GSM is 270Kb/s, the time of each code element is 3.69us. Because the transmission system with BT=0.3 is widely used now, the following...
The current license file does not support the …… device. I am using Quartus9.1, but this problem will occur no matter which device I choose to edit....
I would like to ask, I can use msp430afe253 to measure the voltage when the machine is working, and the error after converting it to current can be 1-2mA, but when the machine is in standby mode, the ...
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
Multi-touch mobile phone
Multi-touch is a system that can respond to multiple touches on the screen at the same time. Multi-touch phones are divided into capacitive and resistive types. Capaci...[Details]
The complexity of the integrated circuits (ICs) used in electronic systems in vehicles is increasing. They aim to execute artificial intelligence (AI) algorithms to control autonomous driving funct...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
Based on the commutation technology, thyristor rectifiers are classified into two main types. Line-commutated and force-commutated inverters are commonly used, while other commutated inverters, nam...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
introduction
With the development of the information superhighway and the internet, broadcast television has become increasingly widespread worldwide. Television information has emerged in var...[Details]
Cadence and NVIDIA Collaborate to Revolutionize Power Analysis Technology, Accelerating Development of Billion-Gate AI Designs
Cadence's new Palladium Dynamic Power Analysis applicat...[Details]
summary
Modern cars strive to provide the same comfort and entertainment features found in the home, resulting in explosive growth in demand for electronic control units (ECUs). Howe...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
With the development of vehicle technology, there are more types of cars. Cars are divided into hybrid, pure electric vehicles, and fuel vehicles. For hybrid cars, they are divided into plug-in hyb...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
