If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage, V
+
Thermal Resistance (θ
JA
) (Note 2)
SO, 8-Pin Small
Outline
MSOP, 8-Pin
Mini Small
Outline
MDIP, 8-Pin
Molded Dip
8-Bump micro
SMD
Maximum
Allowable Power
Dissipation
@
25˚C
MDIP-8
SO-8
MSOP-8
8 Bump micro
SMD
1126 mW
740 mW
555 mW
568 mW
169˚C/W
15V
−0.3V to V
S
+ 0.3V
15V
100 mA
−65˚C to +150˚C
260˚C
215˚C
220˚C
Input Voltages, V
TRIG
, V
RES
, V
CTRL
,
V
THRESH
Output Voltages, V
O
, V
DIS
Output Current I
O
, I
DIS
Storage Temperature Range
Soldering Information
MDIP Soldering (10 seconds)
SOIC, MSOP Vapor Phase (60 sec)
SOIC, MSOP Infrared (15 sec)
225˚C/W
111˚C/W
220˚C/W
Note:
See AN-450 “Surface Mounting Methods and Their Effect on Product
Reliability” for other methods of soldering surface mount devices.
Operating Ratings
(Notes 2, 3)
Termperature
Range
−40˚C to +85˚C
Electrical Characteristics
(Notes 1, 2)
Test Circuit, T = 25˚C, all switches open, RESET to V
S
unless otherwise noted
Symbol
I
S
Parameter
Supply Current
V
S
= 1.5V
V
S
= 5V
V
S
= 12V
V
S
= 1.5V
V
S
= 5V
V
S
= 12V
0.8
2.9
7.4
Conditions
Min
Typ
50
100
150
1.0
3.3
8.0
75
150
0.2
0.3
1.0
1.0
4.4
10.5
0.4
3.7
0.4
0.4
1.25
4.7
11.3
0.5
4.0
10
0.7
0.75
10
10
1.0
0.9
1.0
1.0
1.1
1.1
1.1
0.3
100
1.25
1.20
1.25
1.0
1.1
0.6
4.3
Max
150
250
400
1.2
3.8
8.6
150
300
0.4
0.6
2.0
Units
(Limits)
µA
V
CTRL
Control Voltage
V
V
DIS
V
OL
Discharge Saturation Voltage V
S
= 1.5V, I
DIS
= 1 mA
V
S
= 5V, I
DIS
= 10 mA
Output Voltage (Low)
V
S
= 1.5V, I
O
= 1 mA
V
S
= 5V, I
O
= 8 mA
V
S
= 12V, I
O
= 50 mA
V
S
= 1.5V, I
O
= −0.25 mA
V
S
= 5V, I
O
= −2 mA
V
S
= 12V, I
O
= −10 mA
V
S
= 1.5V
V
S
= 12V
V
S
= 5V
V
S
= 1.5V (Note 4)
V
S
= 12V
V
S
= 5V
V
S
= 5V
V
S
= 12V
SW 2, 4 Closed
V
S
= 1.5V
V
S
= 5V
V
S
= 12V
V
S
= 5V
±
1V
mV
V
V
OH
Output Voltage
(High)
Trigger Voltage
Trigger Current
Reset Voltage
Reset Current
Threshold Current
Discharge Leakage
Timing Accuracy
V
V
TRIG
I
TRIG
V
RES
I
RES
I
THRESH
I
DIS
t
V
pA
V
pA
pA
nA
ms
∆t/∆V
S
Timing Shift with Supply
%/V
3
www.national.com
LMC555
Electrical Characteristics
(Notes 1, 2)
Test Circuit, T = 25˚C, all switches open, RESET to V
S
unless otherwise noted (Continued)
Symbol
∆t/∆T
f
A
f
MAX
t
R
, t
F
t
PD
Parameter
Timing Shift with
Temperature
Astable Frequency
Maximum Frequency
Output Rise and
Fall Times
Trigger Propagation Delay
Conditions
V
S
= 5V
−40˚C
≤
T
≤
+85˚C
SW 1, 3 Closed, V
S
= 12V
Max. Freq. Test Circuit, V
S
= 5V
Max. Freq. Test Circuit
V
S
= 5V, C
L
= 10 pF
V
S
= 5V, Measure Delay
from Trigger to Output
4.0
Min
Typ
75
4.8
3.0
15
5.6
Max
Units
(Limits)
ppm/˚C
kHz
MHz
ns
100
ns
Note 1:
All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3:
See AN-450 for other methods of soldering surface mount devices, and also AN-1112 for micro SMD considerations.
Note 4:
If the RESET pin is to be used at temperatures of −20˚C and below V
Atmega8 microcontroller interrupt serial port receiving problem, the environment is winavr 20100110 version, now to receive data through the serial port, using interrupt mode. Serial port configuratio...
Abstract: One of the important indicators to measure the configuration and design level of Internet system is whether its UPS redundant power supply system has high "reliability", high "availability",...
Dear experts, I use PA12 of port A of STM32L073 as output driver to drive a Bluetooth module, which is equivalent to outputting a low level to wake up the Bluetooth module. I set the push-pull pull-up...
"During the shutdown period, the gate drive level is clamped to zero level. During the on-time of the upper tube of the bridge arm, the driving signal turns on VT1 and turns off VT2, and the drive is ...
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
