EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63116-110Z

Description
MIL-STD-1553 Data Bus Transceiver, FP-24
CategoryWireless rf/communication    Telecom circuit   
File Size125KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63116-110Z Overview

MIL-STD-1553 Data Bus Transceiver, FP-24

BUS-63116-110Z Parametric

Parameter NameAttribute value
MakerData Device Corporation
Parts packaging codeDFP
package instructionDFP,
Contacts24
Reach Compliance Codecompliant
JESD-30 codeR-XDFP-F24
Negative supply voltage rating-15 V
Number of functions1
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialUNSPECIFIED
encapsulated codeDFP
Package shapeRECTANGULAR
Package formFLATPACK
Certification statusNot Qualified
Filter levelMIL-PRF-38534
Maximum seat height4.45 mm
surface mountYES
Telecom integrated circuit typesMIL-STD-1553 DATA BUS TRANSCEIVER
Temperature levelMILITARY
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
Bandpass filter
As long as the bandpass filter is not added to the positive input end of this amplifier circuit, the output will have a waveform. However, after adding the bandpass, there is no square wave. The input...
井子92 Analog electronics
Please help me, great gods
Dear experts, my protel can't open the PCB diagram, and it shows the one in this picture. Does anyone know? ? ? ? ?...
zhaoziyun2011 PCB Design
Two formulas to easily understand current transformers
[i=s]This post was last edited by qwqwqw2088 on 2018-8-14 12:44[/i] [size=4] Using a current transformer can reduce the loss when measuring the primary current of the converter. For example, in a high...
qwqwqw2088 Analogue and Mixed Signal
Wind River's embedded software integrated development environment
Author: Kang Yufeng, Wind River Systems, Inc., USA, Problems faced by embedded system developmentA significant feature of embedded software development that is different from desktop software system d...
fighting Embedded System
DriverStudio2.6 compilation error
My DriverStudio2.6 is installed on drive D. After using DDK Build Setting to enter VC6.0 and compile the library, this error appears in build\batch build: D:\Program Files\NuMega\DriverStudio\DriverWo...
wangencheng Embedded System
Request the specific operation process of PCB equal length serpentine line
Recently, when I was wiring the network card driver, I wanted to perform equal-length wiring for the RMII signal line and the clock line in the way of high-frequency signals. My operation steps are as...
Tobey PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2375  2130  370  1413  1255  48  43  8  29  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号