CD-700KACNEB-60.000 datasheet, PDF

CD-700

Complete VCXO Based Phase Lock Loop

Features

•

5 x 7.5 x 2 mm, smallest VCXO PLL available

•

Output Frequencies to 65.536 MHz

•

5.0 or 3.3 Vdc operation

•

Tri-State Output

•

Loss of Signal Alarm

•

VCXO with CMOS outputs

•

0/70 or –40/85

°C

temperature range

•

Hermetically sealed ceramic SMD package

Applications

•

Frequency Translation

•

Clock Smoothing, Clock Switching

•

NRZ Clock recovery

LOS

(8)

PHO OPN

(3)

(2)

OPOUT

(1)

VC

(16)

LOSIN

(4)

•

DSLAM, ADM, ATM, Aggregation, Optical

Switching/Routing, Base Station

•

Low jitter PLL’s

DATAIN

(5)

CLKIN

(6)

VCXO

Phase

Detector

and LOS

OP-Amp

OUT1

(13)

Description

Optional

n

2 Divider

OUT2

(11)

RCLK RDATA

(9)

(10)

OPP

(15)

GND

(7)

VDD

(14)

HIZ

(12)

The VI CD-700 is a user-configurable crystal

based PLL integrated circuit. It includes a digital

phase detector, op-amp, VCXO and additional

integrated functions for use in digital

synchronization applications. Loop filter software

is available as well SPICE models for circuit

simulation.

Figure 1. CD-700 Block Diagram

Vectron International 166 Glover Avenue, Norwalk CT 06856-5160

Tel:1-88-VECTRON-1

e-mail: vectron@vectron.com

CD-700, VCXO Based PLL

Performance Characteristics

Table 1. Electrical Performance

Parameter

Output Frequency (ordering

option)

OUT1, 5.0 V option

OUT1, 3.3 V option

1

Supply Voltage

+5.0

+3.3

Supply Current

Output Logic Levels

2

Output Logic High

2

Output Logic Low

Output Transition Times

2

Rise Time

2

Fall Time

Input Logic Levels

2

Output Logic High

2

Output Logic Low

Loss of Signal Indication

2

Output Logic High

2

Output Logic Low

Nominal Frequency on Loss of Signal

Output 1

Output 2

3

Symmetry or Duty Cycle

Out 1

Out 2

RCLK

Absolute Pull Range (ordering

option)

over operating temperature, aging, and

power supply variations

Symbol

Min

12.000

Typical

Maximum

65.536

51.840

Units

MHz

V

mA

V

ns

V

ppm

%

ppm

V

DD

4.5

2.97

I

DD

V

OH

V

OL

t

R

t

F

V

IH

V

IL

V

OH

V

OL

2.0

0.5

2.5

0.5

±75

SYM1

SYM2

RCLK

APR

40/60

45/55

40/60

±50

±80

±100

0.5

0.3

Positive

0.53

0.35

0/70 or –40/85

I

VCXO

±1

rad/V

°C

uA

2.5

0.5

5

5.0

3.3

5.5

3.63

63

Test Conditions for APR (+5.0 V option)

Test Conditions for APR (+3.3 V option)

Gain Transfer

Phase Detector Gain

+5V option

+3.3V option

Operating temperature (ordering

option)

Control Voltage Leakage Current

V

C

V

C

4.5

3.0

V

1. A 0.01uF and 0.1uF parallel capacitor should be located as close to pin 14 as possible (and grounded).

2. Figure 2 defines these parameters. Figure 3 illustrates the equivalent five gate TTL load and operating conditions under which

these parameters are tested and specified. Loads greater than 15 pF will adversely effect rise/fall time as well as symmetry.

3. Symmetry is defined as (ON TIME/PERIOD with Vs=1.4 V for both 5.0 V and 3.3 V operation.

t

R

80

%

t

F

I

DD

14

V

DD

+

-

13

7

15pF

650Ω

1.4V

20

%

.

1µF

.01µF

I

C

V

C

16

+

-

On Time

Period

1.8k

Figure 2. Output Waveform

Figure 3. OUT1, OUT2, RCLK, RDATA

Test Conditions (25±5°C)

±

Tel:1-88-VECTRON-1

e-mail: vectron@vectron.com

Vectron International 166 Glover Avenue, Norwalk CT 06856-5160

CD-700, VCXO Based PLL

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional

operation is not implied at these or any other conditions in excess of conditions represented in the

operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may

adversely affect device reliability.

Table 2. Absolute Maximum Ratings

Parameter

Symbol

Power Supply

V

DD

Storage Temperature

Tstorage

Clock and Data Input Range

CLKIN, DATAIN

Ratings

7

-55/125

Gnd-0.5 to V

DD

+0.5

Unit

Vdc

°C

V

Reliability

The CD-700 is capable of meeting the the following qualification tests.

Table 3. Environmental Compliance

Parameter

Mechanical Shock

Mechanical Vibration

Solderability

Gross and Fine Leak

Resistance to Solvents

Conditions

MIL-STD-883, Method 2002

MIL-STD-883, Method 2007

MIL-STD-883, Method 2003

MIL-STD-883, Method 1014, 100% Tested

MIL-STD-883, Method 2016

Handling Precautions

Although ESD protection circuitry has been designed into the the CD-700, proper precautions should be

taken when handling and mounting. VI employs a Human Body Model (HBM) and a Charged Device

Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are

dependent on the circuit parameters used to define the model.

Table 4. Predicted ESD Ratings

Model

Minimum

Human Body Model

Charged Device Model

1500 V

1000 V

Conditions

MIL-STD 883, Method 3015

JESD 22-C101

Vectron International

•

166 Glover Avenue, Norwalk, CT 06856

•

Tel: 1-88-VECTRON-1• http://www.vectron.com

CD-700, VCXO Based PLL

CD-700 Theory of Operation

Phase Detector

The phase detector has two buffered inputs (DATAIN and CLKIN) which are designed to switch at

1.4 volts. DATAIN is designed to accept an NRZ data stream but may also be used for clock signals which

have a 50% duty cycle. CLKIN is connected to OUT1 or OUT2, or a divided version of one of these

outputs. CLKIN and DATAIN and are protected by ESD diodes and should not exceed the power supply

voltage or ground by more than a few hundred millivolts.

The phase detector is basically a latched flip flop/exclusive-or gate/differential amplifier filter design to

produce a DC signal proportional to the phase between the CLKIN and DATAIN signals (see Figure 4 for

a block diagram and Figure 5 for an open loop transfer curve). This will simplify the PLL design as the

designer does not have to filter narrow pulse signals to a DC level. Under locked conditions the rising

edge of CLKIN will be centered in the middle of the DATAIN signal (see Figure 6).

The phase detector gain is 0.53V/rad x data density for 5volt operation and 0.35V/rad x data density for

3.3 volt operation. Data density is equal to 1.0 for clock signals and is system dependent on coding and

design for NRZ signals, but 0.25 could be used as a starting point for data density.

The phase detector output is a DC signal for DATAIN frequencies greater than 1 MHz but produces

significant ripple when inputs are less than 200 kHz. Additional filtering is required for lower input

frequencies applications such as 8kHz (see Figures 8 and 9 as examples).

Under closed loop conditions the active filter has a blocking capacitor which provides a very high DC gain,

so under normal locked conditions and input frequencies >1 MHz, PHO will be about V

DD

/2 and will not

vary significantly with changes in input frequency (within lock range). The control voltage (pin 16) will vary

according to the input frequency offset, but PHO will remain relatively constant.

Data In

(pin 5)

D

Clock In

(pin 6)

Q

1

30 kΩ

20 kΩ

D

Q

2

PHO

(pin 3)

Gain = V

DD

/ 2π

Gain = 2 / 3

Figure 4. Simplified Phase Detector Block Diagram

Vectron International

•

166 Glover Avenue, Norwalk, CT 06856

•

Tel: 1-88-VECTRON-1• http://www.vectron.com

CD-700, VCXO Based PLL

V

DD

−π

V

d

V

DD

/2

0

+π

Relative

Phase (θ

e

)

0V

Gain Slope = V

DD

/ 2π

Figure 5. Open Loop Phase Detector Transfer Curve

Recovered Clock and Data Alignment Outputs

The CD-700 is designed to recover an embedded clock from an NRZ data signal and retime it with a data

pattern. In this application, the VCXO frequency is exactly the same frequency as the NRZ data rate and

the outputs are taken off Pin 9 (RCLK), and Pin 10 (RDATA). Under locked conditions, the falling edge of

RCLK is centered in the RDATA pattern. Also, there is a 1.5 clock cycle delay between DATAIN and

RDATA. Figure 6 shows the relationship between the DATAIN, CLKIN, RDATA and RCLK.

Data In

DATAIN

Clock In

CLKIN

Recovered Data

RDATA

Recovered Clock

RCLK

Data1

Figure 6. Clock and Data Timing Relationships for the NRZ data

Other RZ encoding schemes such as Manchester or AMI can be accomodated by using a CD-700 at twice

the baud rate.

Loss of Signal, LOS and LOSIN

The LOS circuit provides an output alarm flag when the DATAIN input signal is lost. The LOS output is

normally a logic low and is set to a logic high after 256 consecutive clock periods on CLKIN with no

detected DATAIN transitions. This signal can be used to either flag external alarm circuits and/or drive the

CD-700’s LOSIN input. When LOSIN is set to a logic high, the VCXO control voltage (pin 16) is switched

to an internal voltage which sets OUT1 and OUT2 to center frequency +/-75ppm. Also, LOS automatically

closes the op amp feedback which means the op-amp is a unity gain buffer and will produce a DC voltage

equal to the +op amp voltage (pin 15), usually V

DD

/2.

Vectron International

•

166 Glover Avenue, Norwalk, CT 06856

•

Tel: 1-88-VECTRON-1• http://www.vectron.com

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Vectron International, Inc.
Parts packaging code	SOIC
package instruction	HERMETIC SEALED, CERAMIC, SMD-16
Contacts	16
Reach Compliance Code	compliant
Analog Integrated Circuits - Other Types	PHASE LOCKED LOOP
JESD-30 code	R-CQCC-N16
JESD-609 code	e4
length	7.49 mm
Humidity sensitivity level	1
Number of functions	1
Number of terminals	16
Maximum operating temperature	70 °C
Minimum operating temperature
Package body material	CERAMIC, METAL-SEALED COFIRED
encapsulated code	QCCN
Package shape	RECTANGULAR
Package form	CHIP CARRIER
Peak Reflow Temperature (Celsius)	260
Certification status	Not Qualified
Maximum seat height	2.13 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	YES
Temperature level	COMMERCIAL
Terminal surface	GOLD OVER NICKEL
Terminal form	NO LEAD
Terminal pitch	1.02 mm
Terminal location	QUAD
Maximum time at peak reflow temperature	40
width	5.08 mm

CD-700KACNEB-60.000

CD-700KACNEB-60.000 Overview

CD-700KACNEB-60.000 Parametric

Preview

Recommended Resources