EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GI2FC2842

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GI2FC2842 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,

PH1-GI2FC2842 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1533 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Get it for almost 0 Yuan! MPS Power Evaluation Board
From now until April 30, 2023,purchase any development board or chip in the MPS Mall Mini Program . For every 50 yuan of order amount, you can get a 50 yuan JD card. The more you buy, the more you get...
EEWORLD社区 Power technology
Rising edge triggering issue
Regarding the rising edge triggering issue:1. How is the rising edge detected? If the sample taken at the previous time is 0V and the sample taken at the next time is 3V, is it judged that a rising ed...
一沙一世 stm32/stm8
What is the role of this resistor in the AC powered power circuit?
As shown in the figure below, this resistor is often found in AC power supply circuits. What is the function of this resistor?...
Aguilera Power technology
Please help, what is the maximum bps of the RF throughput of the entire ESP32 series?
I want to use ESP32 to send data now. The data volume is about 40Mbps. Is it possible to use ESP32 to send it?...
Int8 Domestic Chip Exchange
How does this current sensing circuit work?
I mainly want to know what circuit the second op amp chip constitutes and what its use is, and why an optocoupler must be connected to it?...
XFJ Analog electronics
I would like to ask about the reset circuit of the microcontroller. When the microcontroller is just powered on and starts to work normally, what is the reset voltage problem?
Regarding the reset circuit of the microcontroller, why is it said that if the waveform of the reset voltage is not steep enough, the microcontroller will not work normally during the period from when...
一沙一世 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1842  2837  561  2830  27  38  58  12  57  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号