EEWORLDEEWORLDEEWORLD

Part Number

Search

3547-021B010

Description
Toggle Switch, DPDT, Momentary, 15A, 28VDC, Solder/quick Connect Terminal, Lever Actuator, Panel Mount-threaded
CategoryMechanical and electronic products    switch   
File Size231KB,5 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

3547-021B010 Overview

Toggle Switch, DPDT, Momentary, 15A, 28VDC, Solder/quick Connect Terminal, Lever Actuator, Panel Mount-threaded

3547-021B010 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeLEVER
body width23 mm
body height31.4 mm
Body length or diameter32 mm
Contact (AC) maximum rated R load15A@125VAC
Maximum contact current (AC)15 A
Maximum contact current (DC)15 A
Contact (DC) maximum rated R load15A@28VDC
Maximum contact voltage (AC)125 V
Maximum contact voltage (DC)28 V
Electrical life6000 Cycle(s)
Manufacturer's serial number3500
Installation featuresPANEL MOUNT-THREADED
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealENVIRONMENTALLY SEALED; IP67; IP64
surface mountNO
Switch actionMOMENTARY
switch functionDPDT
Switch typeTOGGLE SWITCH
Termination typeSOLDER/QUICK CONNECT
3500 series
High performance toggle switches - environmentally sealed
Distinctive features and specifications
Completely sealed switches withstanding 0,1 bar pressure
• Frontal sealing to IP 67 by a silicone membrane
(for sealed panel mounting, add washer U60, section I).
• Rear sealing to IP 64 provided by moulded-in terminal inserts
A
Approved to European standards CECC 96000
Three types of terminals
Many lever styles available
ELECTRICAL SPECIFICATIONS
MATERIALS
• Max. current/voltage rating with resistive load and electrical life at full load:
see table below
• Initial contact resistance : 10 mΩ max. at 1A 2VDC
• Insulation resistance : 1.000 MΩ
• Dielectric strength : 2.500 Vrms 50 Hz min. between terminals
3.000 Vrms 50 Hz min. between terminals and frame
GENERAL PERFORMANCES
FUNCTIONS
Alternate current
6.000 cycles, T65°C
20A 125VAC, 3/4HP
15A 250VAC, 1-1/2HP
T5, 115VAC, 50/400Hz
Direct Current
10.000 cycles, T20°C
15A 28VDC resistive
15A 28VDC inductive
5A 28VDC lamp load
10.000 cycles, T20°C
15A 28VDC resistive
15A 28VDC inductive
5A 28VDC lamp load
10.000 cycles, T20°C
15A 28VDC resistive
10A 28VDC inductive
3A 28VDC lamp load
10.000 cycles
16A 250VAC
15A 32VDC
According to
CECC
96201-004
• Case : mineral filled polyester
UL94-V0
• Bushing and cover : zamac
• Actuator : brass, nickel or chrome
plated, or anodized aluminium
• Contacts : silver alloy
AGENCY APPROVAL
CECC 96201-004
Availability
: consult factory for
details of approved models.
Marking
: to order switches
marked CECC, complete
appropriate box of ordering
format.
ON-OFF
and
ON-ON
6.000 cycles, T65°C
18A 125VAC, 1/2HP
ON OFF ON
10A 250VAC, 1/2HP
T2, 115VAC, 50/400Hz
OTHER
FUNCTIONS
6.000 cycles, T65°C
15A 125VAC
10A 250VAC
T2, 115VAC, 50/400Hz
GENERAL SPECIFICATIONS
• Mechanical life : 40.000 cycles
• Torque : 2 Nm (1.47 Ft.lb) max. applied to nut
• Panel thickness : see “Mounting Accessories” on the following pages
• Operating temperature : -40°c to +85°C
• Moisture resistance : 56 days
A-110
www.apem.com
APEM
RC passive filter circuit and its principle
[b] In the test system, RC filter is often used. Because in this field, the signal frequency is relatively low. The RC filter circuit is simple, has strong anti-interference, has good low-frequency pe...
qwqwqw2088 Analogue and Mixed Signal
ADS8332 Question 2: Where does this interference come from?
I used C2000's SPI to drive ADS8332. I've had success in the past, but it was on a different PCB. However, when I tried it again, I ran into a lot of problems. [/font] Phenomenon: When the sampling an...
dontium Analogue and Mixed Signal
I would like to ask about the timer interrupt problem (I have been unable to find any information, please give me some advice)
Question 1: Is it necessary to install the initial value of the timer in the main function? I seem to have tried it and it works fine without it. Question 2: If timer 0 is turned off in timer 1, do I ...
唐菲远 51mcu
How to implement the 20-bit address pointer of MSP430FG461X series in C language?
When I assign a 20-bit address 0x10000 to a pointer variable, it always says that it is out of the range of 0 to 0xFFFF.This is possible in assembly language, because MSP430X provides instructions wit...
我爱电子 Microcontroller MCU
Crystal oscillator problem
Please help me analyze this:the crystal oscillator is not working properly. It does not oscillate at first. Then I touch it with a soldering iron and it works normally for a while. Then it does not os...
chenzep Microcontroller MCU
Regarding the issue of running programs under pure DOS on the PC104 device, is there any difference between the pure DOS booted by the virtual floppy drive and the actually installed DOS?
As the title says. Now the program runs in pure DOS booted by virtual floppy drive. The program written in 2000 with bc31 runs smoothly in 2000, but it is very stuck in DOS. I want to compile it in DO...
lionedwolf Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2246  994  2263  2612  1850  46  21  53  38  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号