CAV24M01
EEPROM Serial 1-Mb I
2
C
- Automotive Grade 1
Description
The CAV24M01 is a EEPROM Serial 1−Mb I
2
C, internally
organized as 131,072 words of 8 bits each.
It features a 256−byte page write buffer and supports the Standard
(100 kHz), Fast (400 kHz) and Fast−Plus (1 MHz) I
2
C protocol.
Write operations can be inhibited by taking the WP pin High (this
protects the entire memory).
External address pins make it possible to address up to four
CAV24M01 devices on the same bus.
On−Chip ECC (Error Correction Code) makes the device suitable
for high reliability applications.
Features
www.onsemi.com
SOIC−8
W SUFFIX
CASE 751BD
•
•
•
•
•
•
•
•
•
•
•
Automotive Temperature Grade 1 (−40°C to +125°C)
Supports Standard, Fast and Fast−Plus I
2
C Protocol
2.5 V to 5.5 V Supply Voltage Range
256−Byte Page Write Buffer
Hardware Write Protection for Entire Memory
Schmitt Triggers and Noise Suppression Filters on I
2
C Bus Inputs
(SCL and SDA)
Low Power CMOS Technology
1,000,000 Program/Erase Cycles
100 Year Data Retention
8−pin SOIC and TSSOP Packages
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
V
CC
TSSOP−8
Y SUFFIX
CASE 948AL
PIN CONFIGURATION
NC
A
1
A
2
V
SS
SOIC (W), TSSOP (Y)
For the location of Pin 1, please consult the
corresponding package drawing.
1
V
CC
WP
SCL
SDA
PIN FUNCTION
Pin Name
Function
Device Address
Serial Data
Serial Clock
Write Protect
Power Supply
Ground
A
1
, A
2
SDA
SCL
WP
SCL
CAV24M01
SDA
A
2
, A
1
WP
V
CC
V
SS
V
SS
Figure 1. Functional Symbol
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
©
Semiconductor Components Industries, LLC, 2013
May, 2018
−
Rev. 2
1
Publication Order Number:
CAV24M01/D
CAV24M01
MARKING DIAGRAMS
24M01A
AYMXXX
M01C
AYMXXX
G
(TSSOP−8)
(SOIC−8)
24M01A = Specific Device Code
A
= Assembly Location
Y
= Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
XXX = Last Three Digits of
XXX =
Assembly Lot Number
M01C
A
Y
M
XXX
G
= Specific Device Code
= Assembly Location
= Production Year (Last Digit)
= Production Month (1−9, O, N, D)
= Last Three Digits of
=
Assembly Lot Number
= Pb−Free Microdot
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameters
Storage Temperature
Voltage on any Pin with Respect to Ground (Note 1)
Ratings
–65 to +150
–0.5 to +6.5
Units
°C
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The DC input voltage on any pin should not be lower than
−0.5
V or higher than V
CC
+ 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than
−1.5
V or overshoot to no more than V
CC
+ 1.5 V, for periods of less than 20 ns.
Table 2. RELIABILITY CHARACTERISTICS
(Note 2)
Symbol
N
END
(Notes 3, 4)
T
DR
Endurance
Data Retention
Parameter
Min
1,000,000
100
Units
Program/Erase Cycles
Years
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
3. Test Condition: Page Mode, V
CC
= 5 V, 25°C.
4. The device uses ECC (Error Correction Code) logic with 6 ECC bits to correct one bit error in 4 data bytes. Therefore, when a single byte
has to be written, 4 bytes (including the ECC bits) are re-programmed. It is recommended to write by multiple of 4 bytes in order to benefit
from the maximum number of write cycles.
Table 3. D.C. OPERATING CHARACTERISTICS
V
CC
= 2.5 V to 5.5 V, T
A
=
−40°C
to +125°C, unless otherwise specified.
Symbol
I
CCR
I
CCW
I
SB
I
L
V
IL1
V
IH1
V
OL1
Parameter
Read Current
Write Current
Standby Current
I/O Pin Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage
I
OL
= 3.0 mA
Test Conditions
Read, f
SCL
= 400 kHz / 1 MHz
V
CC
= 5.5 V
All I/O Pins at GND or V
CC
Pin at GND or V
CC
T
A
=
−40°C
to +125°C
T
A
=
−40°C
to +125°C
−0.5
0.7 V
CC
Min
Max
1
5.0
5
2
0.3 V
CC
V
CC
+ 0.5
0.4
Units
mA
mA
mA
mA
V
V
V
www.onsemi.com
2
CAV24M01
Table 4. PIN IMPEDANCE CHARACTERISTICS
V
CC
= 2.5 V to 5.5 V, T
A
=
−40°C
to +125°C, unless otherwise specified.
Symbol
C
IN
(Note 5)
C
IN
(Note 5)
I
WP
, I
A
(Note 6)
Parameter
SDA I/O Pin Capacitance
Input Capacitance (other pins)
WP Input Current, Address Input Current (A
1
, A
2
)
Conditions
V
IN
= 0 V
V
IN
= 0 V
V
IN
< V
IH
, V
CC
= 5.5 V
V
IN
< V
IH
, V
CC
= 3.3 V
V
IN
> V
IH
Max
8
6
75
50
2
Units
pF
pF
mA
5. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
6. When not driven, the WP, A
1
, A
2
pins are pulled down to GND internally. For improved noise immunity, the internal pull−down is relatively
strong; therefore the external driver must be able to supply the pull−down current when attempting to drive the input HIGH. To conserve power,
as the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x V
CC
), the strong pull−down reverts to a weak current source.
Table 5. A.C. CHARACTERISTICS
(Note 7) V
CC
= 2.5 V to 5.5 V, T
A
=
−40°C
to +125°C, unless otherwise specified.
Standard
Symbol
F
SCL
t
HD:STA
t
LOW
t
HIGH
t
SU:STA
t
HD:DAT
t
SU:DAT
t
R
(Note 8)
t
F
(Note 8)
t
SU:STO
t
BUF
t
AA
t
DH
T
i
(Note 8)
t
SU:WP
t
HD:WP
t
WR
t
PU
(Notes 8, 9)
Parameter
Clock Frequency
START Condition Hold Time
Low Period of SCL Clock
High Period of SCL Clock
START Condition Setup Time
Data In Hold Time
Data In Setup Time
SDA and SCL Rise Time
SDA and SCL Fall Time
STOP Condition Setup Time
Bus Free Time Between
STOP and START
SCL Low to Data Out Valid
Data Out Hold Time
Noise Pulse Filtered at SCL
and SDA Inputs
WP Setup Time
WP Hold Time
Write Cycle Time
Power-up to Ready Mode
0
2.5
5
0.1
50
50
0
2.5
5
0.1
4
4.7
3.5
50
50
0
1
5
0.1
4
4.7
4
4.7
0
250
1,000
300
0.6
1.3
0.9
50
50
Min
Max
100
0.6
1.3
0.6
0.6
0
100
300
300
0.25
0.5
0.40
Min
Fast
Max
400
0.25
0.45
0.40
0.25
0
50
100
100
Fast−Plus
T
A
=
−405C
to +855C
Min
Max
1,000
Units
kHz
ms
ms
ms
ms
ms
ns
ns
ns
ms
ms
ms
ns
ns
ms
ms
ms
ms
7. Test conditions according to “A.C. Test Conditions” table.
8. Tested initially and after a design or process change that affects this parameter.
9. t
PU
is the delay between the time V
CC
is stable and the device is ready to accept commands.
Table 6. A.C. TEST CONDITIONS
Input Levels
Input Rise and Fall Times
Input Reference Levels
Output Reference Levels
Output Load
0.2 x V
CC
to 0.8 x V
CC
≤
50 ns
0.3 x V
CC
, 0.7 x V
CC
0.5 x V
CC
Current Source: I
L
= 3 mA; C
L
= 100 pF
www.onsemi.com
3
CAV24M01
Power-On Reset (POR)
The CAV24M01 incorporates Power−On Reset (POR)
circuitry which protects the internal logic against powering
up in the wrong state.
The device will power up into Standby mode after V
CC
exceeds the POR trigger level and will power down into
Reset mode when V
CC
drops below the POR trigger level.
This bi−directional POR behavior protects the device
against brown−out failure, following a temporary loss of
power.
Pin Description
SCL:
The Serial Clock input pin accepts the Serial Clock
signal generated by the Master.
SDA:
The Serial Data I/O pin receives input data and
transmits data stored in EEPROM. In transmit mode, this pin
is open drain. Data is acquired on the positive edge, and is
delivered on the negative edge of SCL.
A
1
and A
2
:
The Address pins accept the device address.
These pins have on−chip pull−down resistors.
WP:
The Write Protect input pin inhibits all write
operations, when pulled HIGH. This pin has an on−chip
pull−down resistor.
Functional Description
The CAV24M01 supports the Inter−Integrated Circuit
2
C) Bus data transmission protocol, which defines a device
(I
that sends data to the bus as a transmitter and a device
receiving data as a receiver. Data flow is controlled by a
Master device, which generates the serial clock and all
START and STOP conditions. The CAV24M01 acts as a
Slave device. Master and Slave alternate as either
transmitter or receiver. Up to 4 devices may be connected to
the bus as determined by the device address inputs A
1
and
A
2
.
The I
2
C bus consists of two ‘wires’, SCL and SDA. The
two wires are connected to the V
CC
supply via pull−up
resistors. Master and Slave devices connect to the 2−wire
bus via their respective SCL and SDA pins. The transmitting
device pulls down the SDA line to ‘transmit’ a ‘0’ and
releases it to ‘transmit’ a ‘1’.
Data transfer may be initiated only when the bus is not
busy (see A.C. Characteristics).
I
2
C Bus Protocol
During data transfer, the SDA line must remain stable
while the SCL line is HIGH. An SDA transition while SCL
is HIGH will be interpreted as a START or STOP condition
(Figure 2).
START
The START condition precedes all commands. It consists
of a HIGH to LOW transition on SDA while SCL is HIGH.
The START acts as a ‘wake−up’ call to all receivers. Absent
a START, a Slave will not respond to commands.
STOP
The STOP condition completes all commands. It consists
of a LOW to HIGH transition on SDA while SCL is HIGH.
The STOP starts the internal Write cycle (when following a
Write command) or sends the Slave into standby mode
(when following a Read command).
Device Addressing
The Master initiates data transfer by creating a START
condition on the bus. The Master then broadcasts an 8−bit
serial Slave address. The first 4 bits of the Slave address are
set to 1010, for normal Read/Write operations (Figure 3).
The next 2 bits, A2, A1, select one of 4 possible memory
devices connected on a single I
2
C bus. The A2 and A1 bits
must match the state of the external address pins. The
seventh bit, a16 is the most significant internal address bit.
The last bit, R/W, specifies whether a Read (1) or Write (0)
operation is to be performed. To select an internal memory
location (data byte) a 17−bit address word is required:
a16 bit from the Slave address byte followed by two address
bytes.
Acknowledge
After processing the Slave address, the Slave responds
with an acknowledge (ACK) by pulling down the SDA line
during the 9th clock cycle (Figure 4). The Slave will also
acknowledge the byte address and every data byte presented
in Write mode. In Read mode the Slave shifts out a data byte,
and then releases the SDA line during the 9th clock cycle. If
the Master acknowledges the data, then the Slave continues
transmitting. The Master terminates the session by not
acknowledging the last data byte (NoACK) and by sending
a STOP to the Slave. Bus timing is illustrated in Figure 5.
www.onsemi.com
4
CAV24M01
SCL
SDA
START
CONDITION
STOP
CONDITION
Figure 2. Start/Stop Timing
1
0
1
0
A
2
A
1
a
16
R/W
DEVICE ADDRESS
Figure 3. Slave Address Bits
BUS RELEASE DELAY (TRANSMITTER)
SCL FROM
MASTER
DATA OUTPUT
FROM TRANSMITTER
1
8
9
BUS RELEASE DELAY (RECEIVER)
DATA OUTPUT
FROM RECEIVER
START
ACK DELAY (≤ t
AA
)
ACK SETUP (≥ t
SU:DAT
)
Figure 4. Acknowledge Timing
t
F
t
LOW
SCL
t
SU:STA
SDA IN
t
AA
SDA OUT
t
HD:STA
t
HIGH
t
LOW
t
R
t
HD:DAT
t
SU:DAT
t
SU:STO
t
DH
t
BUF
Figure 5. Bus Timing
www.onsemi.com
5
京公网安备 11010802033920号
EEWORLD
