Ruthenium oxide dielectric offers superior resistance
to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1982 (first in the wold), this
component has established a solid reputation as a
general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°C
.
100
80
60
40
20
0
Specifications
0.125W (1 / 8W)
[0.100W (1 / 10W)]
∗
at 70°C
POWER LOAD (%)
– 55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E = P× R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
* At power rating of 0.1W, maximum overload voltage and maximum intermittent overload voltage are 300V.
Max. operating voltage
150V
200V
(300V)
∗
Max. overload voltage
Max. intermittent overload voltage 200V
(300V)
∗
See Table 1.
– 55
°C
to + 155
°C
MCR10
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
J ( ± 5%)
Table 1
Resistance tolerance
F ( ± 1%)
Resistance range
(Ω)
10
≤
R
≤
2.2M (E24,96)
1.0
≤
R
<
2.2
2.2
≤
R
<
10
10
≤
R
<
10M
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature – 55°C to + 155°C
!Before
using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
MCR10
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
±
(2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F:
±
1%
J:
±
5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 / – 55 / + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 200V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
±
(5.0% + 0.1Ω)
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON – 25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260
±
5°C
Soldering time: 10
±
1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235
±
5°C
Soldering time: 2.0
±
0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 90%RH
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature: – 55°C to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
Max. 50mΩ
±
(1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
±
(1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Temperature cycling
±
(1.0% + 0.05Ω)
Max. 50mΩ
Resistance to solvents
Max. 50mΩ
±
(0.5% + 0.05Ω)
Markings must not be dissolved away.
MCR10
Resistors
!External
dimensions
(Units: mm)
0.4 ± 0.2
No.
0.4 ± 0.2
2.0 ± 0.1
0.55 ± 0.1
Material
Thick dielectric glaze of ruthenium
(only silver used for jumper)
Thick film of palladium-silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
1.25 ± 0.1
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
Open the FPGA design interface, and the following figure is mainly displayed. First, select the FPGA required by the design, temporarily select A3P1000, then select the required power supply, and then...
I found that some demos on the Internet that use Microsoft's CryptoAPI library for digital signatures are all RSA signatures, and the public and private key pairs for signatures are generated by the f...
I didn't expect that 2015 will be over soon. I'm not ready to welcome the new year. Although I'm reluctant to see 2015 go by, it seems that I can't stop it. It disappears from my fingers and keyboards...
I want to display the printed content on the vxworks tornado shell on the interface of a PC program I wrote. Can I do it through the shell redirection function? Please give me some advice!!!...
introduction
Oxygen is an important substance for human metabolism. Brain tissue has a high metabolic rate and consumes about 20% of the total oxygen in the body. In the clinical rescue and ...[Details]
At present, the global medical electronics industry is gradually showing attractive development prospects, and the speed of product replacement is constantly increasing. At the same time, due to the p...[Details]
Controller Area Network (CAN) is a type of fieldbus. It is a serial communication network that effectively supports distributed control or real-time control and is recognized as one of the most pro...[Details]
Due to the needs of medical development, in many cases, general thermometers can no longer meet the requirements of fast and accurate temperature measurement, such as measuring human body temperature ...[Details]
Demand Analysis
In an era of rapid information development, the process of electronicization of the financial system has also been greatly accelerated. As a platform that provides services 24 ...[Details]
MOSFETs are widely used as power switching elements in regulators and motor controllers. They are available as discrete devices or integrated into ICs in various H-bridge configurations.
A hig...[Details]
1 Introduction
Generally, when transmitting information over short distances through electrical signals, baseband signals can be directly transmitted. However, over long distances, baseban...[Details]
1 Introduction
Reliability research originated from weapon systems. After nearly half a century of development, it has become an engineering discipline that covers all disciplines and industri...[Details]
Introduction: Generally speaking, the power supplies used to drive today's high-resolution analog/digital converters have AC or DC loads of hundreds of ohms or more. Therefore, an operational ampli...[Details]
With the improvement of people's requirements for vehicle riding comfort and the development of passenger car suspension technology in my country, air suspension is increasingly used in passenger ...[Details]
With the advent of the new economic era represented by the Internet, PCs have lost their former glory, and smart 3C products (Computer, Communication and Consumer) will set off a new wave. As one o...[Details]
Automatic target recognition (ATR) algorithms usually include algorithms for automatically detecting, tracking, identifying, and selecting attack points for targets. The complexity of the battlefi...[Details]
This Design Idea shows how to keep telecom equipment operational during brief brownouts. First, it is important to understand a few details about the power supplies used for telecom equipment. The ...[Details]
The third generation iPhone, iPhone 3G S, has finally been released. Let's take a look at the differences in basic parameters between it and the previous generation iPhone 3G.
According to for...[Details]
1 Introduction
Under the current situation of power shortage in my country, it is very important to monitor power to ensure safe use of power. The research and transformation of power grid...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
