EEWORLDEEWORLDEEWORLD

Part Number

Search

3199GG683M075ANR1

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 75V, 20% +Tol, 20% -Tol, 68000uF, Stud Mount, CAN, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size88KB,7 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance
Download Datasheet Parametric View All

3199GG683M075ANR1 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 75V, 20% +Tol, 20% -Tol, 68000uF, Stud Mount, CAN, ROHS COMPLIANT

3199GG683M075ANR1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerCDE [ CORNELL DUBILIER ELECTRONICS ]
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance68000 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter76.2 mm
dielectric materialsALUMINUM (WET)
ESR5 mΩ
length130.2 mm
Manufacturer's serial number3199
Installation featuresSTUD MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
Package shapeCYLINDRICAL PACKAGE
Package formScrew Ends
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)75 V
ripple current27500 mA
series3199
surface mountNO
Terminal pitch31.8 mm
Terminal shapeBINDING POST
Type 3199 Aluminum Electrolytic, Screw Terminals
Screw Terminal Capacitors for Power Output Filtering
With twice the capacitance of Type 3191 capacitor, Type 3199
extends output filtering performance into higher power,
especially with cold temperature requirements. Standard
encasement is with the capacitor element compressed onto
an aluminum peg in the can bottom and a phenolic peg in
the top. Optional Rilled construction is available. With rilled
construction the element is secured by rills, spoon shaped
dimples in the side of the can. Rilled construction offers
the industries highest vibration and shock withstanding
capability and excellent heat transfer.
Highlights
- Stud mount available
- High current application
- Industrial applications
- Smoothing and filtering
- Audio power supplies
–55 ºC to +85 ºC
7.5 Vdc to 75 Vdc
3900 µF to 1.2 F
–10% +30%
–10% +50%
≤6√CV µA (6 mA max.) at 5 minutes
Ambient Temperature
45 °C
2.24
Frequency
60 Hz 120 Hz
16 – 100 V
Low Temperature Characteristics
0.90
1.00
300 Hz
1.05
1000 Hz
1.10
≥10
kHz
1.15
55 °C
2.00
65 °C
1.73
75 °C
1.41
85 °C
1.00
Specifications
Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Ripple Current Multipliers
Impedance ratio: Z
–20⁰C
∕ Z
+25⁰C
≤ 8 (16–50 Vdc)
≤ 4 (63–75Vdc)
Endurance, 5000 h at rated voltage and 85 ºC
Δ Capacitance: ±10%
ESR ≤ 200% of limit
DCL ≤ 100% of limit
Storage, 500 h at 85 ºC
Δ Capacitance: ±10%
ESR ≤ 175% of limit
DCL ≤ 200% of limit
10 to 500 Hz, 0.75 mm or 10 g* if less, 3 directions, 2 h ea
Δ Capacitance: ±5%
no visible damage or leakage
*15 g if rilled construction
RoHS Compliant
Endurance Life Test
Shelf Life Test
Vibration
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
52 single chip read and write AT25F128
I'm working on the read and write program of AT25F128 recently. It's SPI port! But, it can't be successful. Any reference? My CS signal is directly grounded, is it not working? Must I connect a pin?! ...
后学 Embedded System
It’s so funny, reporters are really tough!
1. The leader just got off the plane, and the reporter asked: What do you think of prostitutes? The leader was surprised: There are prostitutes in Beijing? The reporter published an article in the new...
wljmm Talking
Application skills/Atmel microcontroller application skills
Powerful clock interruptClick here to download a PDF of this pageIn program design, setting a good clock interrupt can greatly facilitate and simplify program compilation and improve system efficiency...
rain Microchip MCU
TI_DSP_C2000 Series_Introduction and Selection
[b][size=4]TI__DSP_C2000 Series_Introduction and Selection[/size][/b] [b][size=4][/size][/b]...
Jacktang Microcontroller MCU
Allwinner V5 helloworld example (test your entire development environment) --- lindeni V5 development board
[i=s]This post was last edited by IC Crawler on 2020-1-29 09:22[/i]There are instructions for building cross-tools in this post https://bbs.eeworld.com.cn/thread-1108671-1-1.html ! This post requires:...
IC爬虫 Special Edition for Assessment Centres
The charger has a glitch problem when it is powered on
I made a 18650 lithium battery charging circuit. The charger uses a 5V 2A mobile phone charger. A TP5100 is used as a lithium battery charging IC on the board. The circuit diagram is as follows. The c...
MrKingMCU Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1519  1047  2062  1945  2360  31  22  42  40  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号