EEWORLDEEWORLDEEWORLD

Part Number

Search

SC25M220AZF3811

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SC25M220AZF3811 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, ROHS COMPLIANT

SC25M220AZF3811 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance220 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR130 mΩ
leakage current0.055 mA
Manufacturer's serial numberSC
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)25 V
ripple current640 mA
surface mountNO
Delta tangent0.1
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SC
[ For Low Impedance and Low E.S.R
Suitable for Output of Mother Board ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DESCRIPTION
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 3000
Hours
DC Leakage Current (µA) : I = 0.01 CV(µA) or 3µA Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 15
14
12
10
10
8
8
7
7
For capacitor whose capacitance exceeds 2000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
10
10
8
16
5
25
4
35
4
50
4
63
4
100
4
Impedance : Z - 40°C / Z + 20°C
Load Life : 3000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency(Hz)
~4.7µF
5.6~33µF
34~330µF
331~1000µF
1200µF Higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.80
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K 100K
0.80 1.00
0.90 1.00
0.95 1.00
1.00 1.00
1.00 1.00
5 x 11 ~ 10 x 12 : Life = 2000 Hours
10 x 15 or Higher : Life = 3000 Hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
I want to start a training on single chip microcomputer. Is there any need?
As the moderator, I would like to start a topic about MCU training. I would like to organize the information including hardware schematics, programs and documentation according to the characteristics ...
njlianjian MCU
About handling unused I/O pins
One issue that can cause higher than expected current consumption is turning on the input. To prevent turning on the input, use one of the following solutions for unused I/O pins:Switch unused I/Os to...
vicer Microcontroller MCU
Is the advantage of C2000 just its fast processing speed?
I received the C2000 28035 development board from TI today. I want to ask what are the specific advantages of C2000 over ARM. I feel that the resources of 28035 are not as good as those of M3 ARM, and...
fengzhang2002 Microcontroller MCU
Solution to ARM debugging DAbt_Handler problem
[i=s]This post was last edited by Aguilera on 2019-9-3 22:27[/i]ARM: How to analyze a DAbt exceptionThis article is for:Any version of ARMProblem:My ARM application does not work. When I run it in a s...
Aguilera Microcontroller MCU
I would like to ask some questions about the 5 LPM modes?
1. How to use LPM mode? ? The sheet says that it involves four bits in SR: SCG0, SCG1, CPuOFF, OSCOFF.But there are only five LPM combinations. Can we only operate according to the five listed in the ...
autodut Microcontroller MCU
Q2 Why does the MOS tube get hot and damaged?
[i=s]This post was last edited by aq1261101415 on 2020-9-24 18:50[/i]Q2 Why does the MOS tube get hot and damaged? Is it because there is no freewheeling diode in the motor? However, I cannot find a f...
aq1261101415 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 989  1528  1912  1037  1444  20  31  39  21  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号