EEWORLDEEWORLDEEWORLD

Part Number

Search

SC50M1200B2SL1632

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 1200uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SC50M1200B2SL1632 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 1200uF, Through Hole Mount, ROHS COMPLIANT

SC50M1200B2SL1632 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance1200 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR25 mΩ
leakage current0.6 mA
Manufacturer's serial numberSC
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)50 V
ripple current2100 mA
surface mountNO
Delta tangent0.08
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SC
[ For Low Impedance and Low E.S.R
Suitable for Output of Mother Board ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DESCRIPTION
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 3000
Hours
DC Leakage Current (µA) : I = 0.01 CV(µA) or 3µA Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 15
14
12
10
10
8
8
7
7
For capacitor whose capacitance exceeds 2000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
10
10
8
16
5
25
4
35
4
50
4
63
4
100
4
Impedance : Z - 40°C / Z + 20°C
Load Life : 3000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency(Hz)
~4.7µF
5.6~33µF
34~330µF
331~1000µF
1200µF Higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.80
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K 100K
0.80 1.00
0.90 1.00
0.95 1.00
1.00 1.00
1.00 1.00
5 x 11 ~ 10 x 12 : Life = 2000 Hours
10 x 15 or Higher : Life = 3000 Hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
High-frequency synchronous rectification problem
If I want to change the rectifier here to synchronous rectification (500kHz), what solution should I use? I checked it myself at night, but I didn't understand it clearly. The front end is a coupled r...
华南 Power technology
BSL download program problem of MSP430F149
I just started learning 430 and I am using MSPFET. I followed the normal setting method for basic settings. I want to use BSL to download the program, but I can reset it but cannot download it. It say...
wsbegin2011 Microcontroller MCU
Getting Started
void Init_Clk(void) { P7SEL |= 0x03; // XT1 starts oscillating UCSCTL1 = DCORSEL_6; // Select the range of DCO UCSCTL2 |= 240; // Set DCO frequency to 16M UCSCTL4 = SELM_3 + SELA_0 + SELS_4; // Set MC...
羽翼之杨勇0102 Microcontroller MCU
Why are there so many errors in the circuit diagram? Please help me check it out. Thank you.
I designed a circuit diagram using protel99. After simulation and execution, I found many errors. Are these errors normal? Do I need to modify them? The following are some errors: CAP Error: Pin order...
haian_bch Embedded System
High precision temperature controller
[indent][indent][align=left]Using 555 chip and NTC thermal sensor, the control accuracy can reach 0.05°C in the range of -6 to +46°C. It communicates with the computer via RS232 every 2 seconds. It ca...
咖啡不加糖 MCU
I need to solve a problem, please help
My ADC is powered by 1.8 V. How can it have a 2 V pp input range?...
顶顶 ADI Reference Circuit

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2182  845  903  778  661  44  18  19  16  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号