family of ultra-low rms jitter oscillators is now available in a miniature 2.5 x 2.0 x
1.0 mm package. The AK2 family is based on 3rd overtone quartz crystal technology and is ideally suited for optical transceivers,
networking and server systems. AK2 family is available with bias voltages of 3.3V and 2.5V for LVDS & LVPECL output
configuration; and 3.3V, 2.5V & 1.8V for HCSL differential output. Production-ready frequencies include 100, 125, 148.5, 156.25
and 200MHz with better than ±30 ppm frequency stability over -40°C
to +85°C operating temperature range.
The AK2 family offers best-in-class rms phase jitter of <110 fs typical at 156.25MHz carrier @ V
dd
= +2.5V with LVDS output, and
is guaranteed to exhibit <200fs rms jitter @ 156.25MHz carrier with any bias voltage and RF output configuration.
2.5 x 2.0 x 1.0 mm
RoHS/RoHS II
Compliant
MSL = 1
ESD Sensitive
Pb
Features
•
Based on 3rd Overtone, Quartz Crystal Technology
•
Ultra-low rms jitter; < 120fs typical @ 156.25MHz
•
Lowest in-class power consumption (15mA max with LVDS)
•
±25ppm max & ±30ppm max stability over -20°C to +70°C
and -40°C to +85°C respectively
•
3.3V, 2.5V & 1.8V supply voltage options
•
LVPECL, LVDS and HCSL differential output options
•
Output enabled (Active High standard default)
Applications
•
•
•
•
•
•
•
•
•
•
•
•
Optical Transceivers
Optical Modules
Networking and communications
Gigabit Ethernet
Fibre Channel
SONET/SDH
RF systems, base stations (BTS)
Datacenter
PCI Express
Test & measurement
Active cables
Compact HD-SDI cameras
Options and Part Identification
[Note 1]
AK2
(1): Output
P: LVPECL
D: LVDS
H: HCSL
(6): Packaging
(3): Stability over OTR
D: ±25ppm over -20°C to +70°C
F: ±30 ppm over -40°C to +85°C
Blank: Bulk (***)
T: Tape & Reel 1,000 units
T3: Tape & Reel 3,000 units
(***) MOQ: 100 units
A: 3.3V
B: 2.5V
C: 1.8V (*)
(*) Excluding
LVPECL
(2): V
dd
(4): OE Function
1: OE Pin 1; Active High
2: OE Pin 2; Active High
(5): Output Frequency
in MHz
Please specify the frequency in
units of MHz out to
4 digit
accuracy after the decimal.
Example:
“156.2500”=156.25MHz
Part Number Example:
AK2PAF1-156.2500
AK2PAF1-156.2500T
AK2PAF1-156.2500T3
[(100) units in Bulk]
[(1k) units on Tape & Reel]
[(3k) units on Tape & Reel]
Note 1: Contact Abracon for non-standard part number configurations and/or requests with carrier frequency callouts up to 5 & 6 digit accuracy after the decimal.
The most impressive thing is that Flash is mapped to PM, with only a small amount of SRAM on the chip; this makes the Load Program method completely ineffective during program debugging, and always pr...
FPGA video transmission : https://training.eeworld.com.cn/course/2133In this example, two VEEK-MT FPGA development platforms are used to transmit video to each other through analog-to-digital converte...
This time, we will conduct a power-on experiment on the development board. First, we will burn the Tina system. The Tina system is a system developed by Allwinner for the modified OpenWRT1404 . It is ...
Generally speaking, the emulator is used for debugging and emulation, and the programmer is used to burn the target code to the MCU during mass production.For MSP430, both emulation and burning progra...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
