C330C912JCG5CA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> capacitor> C330C912JCG5CA

C330C912JCG5CA: DescriptionCAPACITOR, CERAMIC, MULTILAYER, 500V, C0G, 0.0091uF, THROUGH HOLE MOUNT, RADIAL LEADED; CategoryPassive components capacitor; File Size2MB，11 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com; Environmental Compliance

Download Datasheet Parametric View All

C330C912JCG5CA Overview

CAPACITOR, CERAMIC, MULTILAYER, 500V, C0G, 0.0091uF, THROUGH HOLE MOUNT, RADIAL LEADED

C330C912JCG5CA Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	KEMET
package instruction	, 3025
Reach Compliance Code	not_compliant
ECCN code	EAR99
capacitance	0.0091 µF
Capacitor type	CERAMIC CAPACITOR
dielectric materials	CERAMIC
high	9.14 mm
JESD-609 code	e3
length	7.62 mm
Manufacturer's serial number	C330
Installation features	THROUGH HOLE MOUNT
multi-layer	Yes
negative tolerance	5%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	RECTANGULAR PACKAGE
Package form	Radial
method of packing	BULK
positive tolerance	5%
Rated (DC) voltage (URdc)	500 V
series	C33(C0G,500V,J TOL)
size code	3025
surface mount	NO
Temperature characteristic code	C0G
Temperature Coefficient	-/+30ppm/Cel ppm/°C
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrier
Terminal pitch	5.08 mm
Terminal shape	WIRE
width	6.35 mm

Preview

Download Datasheet

View All

MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED

Multilayer ceramic capacitors are available in a

variety of physical sizes and configurations, including

leaded devices and surface mounted chips. Leaded

styles include molded and conformally coated parts

with axial and radial leads. However, the basic

capacitor element is similar for all styles. It is called a

chip and consists of formulated dielectric materials

which have been cast into thin layers, interspersed

with metal electrodes alternately exposed on opposite

edges of the laminated structure. The entire structure is

fired at high temperature to produce a monolithic

block which provides high capacitance values in a

small physical volume. After firing, conductive

terminations are applied to opposite ends of the chip to

make contact with the exposed electrodes.

Termination materials and methods vary depending on

the intended use.

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with

Class III:

General purpose capacitors, suitable

a wide range of characteristics. The EIA standard for

for by-pass coupling or other applications in which

ceramic dielectric capacitors (RS-198) divides ceramic

dielectric losses, high insulation resistance and

dielectrics into the following classes:

stability of capacitance characteristics are of little or

no importance. Class III capacitors are similar to Class

II capacitors except for temperature characteristics,

Class I:

Temperature compensating capacitors,

which are greater than ± 15%. Class III capacitors

suitable for resonant circuit application or other appli-

have the highest volumetric efficiency and poorest

cations where high Q and stability of capacitance char-

stability of any type.

acteristics are required. Class I capacitors have

predictable temperature coefficients and are not

effected by voltage, frequency or time. They are made

KEMET leaded ceramic capacitors are offered in

from materials which are not ferro-electric, yielding

the three most popular temperature characteristics:

superior stability but low volumetric efficiency. Class I

C0G:

Class I, with a temperature coefficient of 0 ±

capacitors are the most stable type available, but have

30 ppm per degree C over an operating

the lowest volumetric efficiency.

temperature range of - 55°C to + 125°C (Also

known as “NP0”).

X7R:

Class II, with a maximum capacitance

Class II:

Stable capacitors, suitable for bypass

change of ± 15% over an operating temperature

or coupling applications or frequency discriminating

range of - 55°C to + 125°C.

circuits where Q and stability of capacitance char-

Z5U:

Class III, with a maximum capacitance

acteristics are not of major importance. Class II

change of + 22% - 56% over an operating tem-

capacitors have temperature characteristics of ± 15%

perature range of + 10°C to + 85°C.

or less. They are made from materials which are

ferro-electric, yielding higher volumetric efficiency but

Specified electrical limits for these three temperature

less stability. Class II capacitors are affected by

temperature, voltage, frequency and time.

characteristics are shown in Table 1.

SPECIFIED ELECTRICAL LIMITS

PARAMETER

Dissipation Factor: Measured at following conditions:

C0G — 1 kHz and 1 vrms if capacitance > 1000 pF

1 MHz and 1 vrms if capacitance

≤

1000 pF

X7R — 1 kHz and 1 vrms* or if extended cap range 0.5 vrms

Z5U — 1 kHz and 0.5 vrms

Dielectric Strength: 2.5 times rated DC voltage.

Insulation Resistance (IR): At rated DC voltage,

whichever of the two is smaller

Temperature Characteristics: Range, °C

Capacitance Change without

DC voltage

* 1 MHz and 1 vrms if capacitance

≤

100 pF on military product.

TEMPERATURE CHARACTERISTICS

C0G

X7R

Z5U

0.15%

2.5%

4.0%

Pass Subsequent IR Test

1,000 MΩ-µF

or 100 GΩ

-55 to +125

0 ± 30 ppm/°C

1,000 MΩ-µF

or 100 GΩ

-55 to +125

±15%

1,000 MΩ-µF

or 10 GΩ

+10 to +85

+22%, -56%

Table I

Multlayer Ceramic

Capacitors

Recommended Resources

Use LS7232 to create a touch-sensitive dimming light

Offline Flyback Regulator Circuit

Basic application circuit diagram of MAX680

22 commonly used diode single-phase rectifier circuits Figure 3

Large water tower automatic control water supply circuit diagram

Photometric circuit using PbS, PbSe

Things to note when routing high-frequency and high-speed signal lines along the edge of a PCB: [align=left][color=rgb(51, 51, 51)]We often see some design principles about high-frequency and high-speed signals in textbooks or original PCB Design Guides, including not running high-speed signal l...; okhxyyo PCB Design

Ideas alone are not enough: Yes, it is important to have new ideas. However, in any great innovation story, good ideas are only the beginning. A hundred years ago, Thomas Edison said, "Genius is 1% inspiration and 99% hard work....; zhangang Talking

MSP430G2553 Timer Interrupt Example: [i=s] This post was last edited by fish001 on 2017-9-15 22:42 [/i] #include "MSP430G2553.h" void led_init(); void timer0_init(); void main( void ) { // Stop watchdog timer to prevent time out reset WD...; fish001 Microcontroller MCU

Problems with sampling MSP430F149AD: [i=s] This post was last edited by paulhyde on 2014-9-15 03:00 [/i] Why does the AD sampling port output a high level upon startup? It is the maximum value of the reference voltage for AD. I have set ...; shannon2014 Electronics Design Contest

PLC, what is so difficult about it? [Transfer]: If a company with strong financial resources like Emerson has given up the PLC business, what should more PLC companies that rely on rolling development do? It is undeniable that as an investment comp...; wanggq Industrial Control Electronics

Usage of DIP switch in address identification: How to use the DIP switch to indicate the address of a module? How to connect the DIP switch to the microcontroller? Please give me some advice. Thank you....; sunshinehoney MCU

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components