5GSR42G-B-100T-FREQ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 5GSR42G-B-100T-FREQ

5GSR42G-B-100T-FREQ: DescriptionSine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN; CategoryPassive components oscillator; File Size93KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric View All

5GSR42G-B-100T-FREQ Overview

Sine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN

5GSR42G-B-100T-FREQ Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Euroquartz
Reach Compliance Code	compliant
Maximum control voltage	4.5 V
Minimum control voltage	0.5 V
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	100 ppm
frequency stability	50%
Installation features	SURFACE MOUNT
Maximum operating frequency	30 MHz
Minimum operating frequency	10 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	SINE
Output impedance	10000 Ω
Output level	1 V
physical size	11.4mm x 9.6mm x 2.5mm
Maximum supply voltage	5.25 V
Minimum supply voltage	4.75 V
Nominal supply voltage	5 V
surface mount	YES

Preview

Download Datasheet

View All

EURO

QUARTZ

FEATURES

Sine Wave output VCXO

Output 10k //10pF load, 1.0V p-p

Harmonics < 25dBc

Low current consumption

GSR42 Sine Wave VCXOs

11.4 x 9.6 x 2.5mm SMD Sine Wave VCXO

OUTLINE & DIMENSIONS

DESCRIPTION

GSR42 sine wave VCXOs provide a true sine wave out output. The

VCXOs are packaged in the industry-standard, 4 pad 11.4 x 9.6mm

SMD package. The VCXO is produced to close tolerances and has low

current consumption.

SPECIFICATION

Frequency Range:

Input Voltage:

Frequency Stability:

Control Voltage Centre:

Initial Frequency Accuracy:

Control Voltage Range:

Frequency Deviation Range:

Output Wave Form:

Output Level:

Harmonics:

Phase Noise:

Current Consumption

Supply = 2.8V:

Supply = 3.3V:

Supply = 5.0V:

Start-up Time:

Storage Temperature:

Sub-Harmonics:

Ageing:

Enable/Disable:

RoHS Status:

10.0MHz to 30.0MHz

+2.8V, +3.3V±5% or +5.0VDC ±5%

See table

+2.5 VDC

±15ppm with Conrol V at +2.5VDC

+0.5V to +4.5VDC

±100ppm typical*

True Sine Wave

10k //10pF load, 1.0V p-p

<-25dBc

-130dBc/Hz at 1kHz offset

1.0mA

1.1mA

1.2mA

2.0ms typical

-50° to +125°C

None

±5ppm per year maximum

Not implemented - 4 pad package

Fully compliant or non-compliant

* Wider pulling range available

FREQUENCY STABILITY

Stability Code Stability ±ppm Temp. Range

0°~+70°C

100

0°~+70°C

-40°~+85°C

100

-40°~+85°C

If non-standard frequency stability is required

Use ‘I’ followed by stability, i.e. I20 for ±20ppm

PART NUMBERING

Example:

Supply Voltage

3 = 3.3 Volts

5 = 5.0 Volts

Series Designation

GSR42

RoHS Status

G = compliant

Blank = non-compliant

Frequency Stability

See table

Pull Range

±ppm

Pull Range Code

M = Maximum

N = Minimum

T = Typical

Frequency

MHz

3GSR42G-A-80N-25.000

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

Acousto-optic digital level detector circuit diagram

Separately excited DC motor forward and reverse circuit

Head amplifier dedicated power supply circuit

Water full alarm circuit

Illuminance meter circuit diagram

long timer circuit

IP address problem: [color=rgb(68, 68, 68)][font=Tahoma,]There are two IP addresses here. Which one should I use when connecting to GPRS? The first one is the external network, and the second one is the internal network....; chenbingjy stm32/stm8

How to design a circuit to prevent power supply reverse junction?: [i=s]This post was last edited by dianhang on 2016-8-3 14:23[/i] [size=3]My power input is between 10-24V. I want to use MOS tubes to prevent power reverse junction. How should I design it? [/size]...; dianhang Power technology

The resistance of the transistor: What is the function of the resistor in the red part in the picture above and how to choose its value? Please give me some advice...; cpfpost LED Zone

setIcon() in EVC does not respond: Declaration: CWnd* tryIcon; HICON myIcon2; The code in OnInitDialog() is as follows: tryIcon = (CWnd*)GetDlgItem(bj); //bj is a picture control manually dragged onto the dialog; tryIcon->SetIcon(AfxGe...; sanwa_chen Embedded System

LM8962 learning experience - query method control buttons and lights: The student finally finished the exam, so he took the time to study 8962. This time he used the query method to control buttons and lights....; youki12345 Microcontroller MCU

MSP430F11x2, MSP430F12x, MSP430F12x2 official sample code: The code in the attachment is the sample code officially released by TI, which can be used as a reliable code reference for learning and using MSP430 [[i] This post was last edited by wstt on 2012-5-3...; wstt Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components